60 Watts xppower.com SDS Series Single, Dual, Triple & Quad Outputs Output Voltages from 3.3 V to 48 V Non standard Outputs Available Industry Standard 3 x 5 Package Fits 1U Applications Open Frame, U Channel & Covered Versions 3 Year Warranty Specification Input General Input Voltage 90-264 VAC (120-370 VDC) Efficiency 80% typical, 230 VAC full load Input Frequency 47-63 Hz Isolation 3000 VAC Input to Output 1500 VAC Input to Ground Input Current 1.6 A max at 115 VAC 500 VDC Output to Ground 1.0 A max at 230 VAC Switching Frequency 60 kHz typical Inrush Current <15 A at 115 VAC, cold start at 25 C 3 <30 A at 230 VAC, cold start at 25 C Power Density 3.5 W/In Earth Leakage Current <0.30 mA at 115 VAC Signals Green DC OK LED <0.75 mA at 240 VAC MTBF 190 kHrs typical to MIL-HDBK-217F Power Factor EN61000-3-2, Class A at 25 C, GB Input Protection T2 A/250 VAC internal fuse in line Environmental Output Operating Temperature 0 C to +70 C, derate linearly from 100% load at +50 C to 50% load at +70 C Output Voltage See table Cooling Convection-cooled Output Voltage Trim 10% on V1 only (see note 4) Operating Humidity 5-95% RH, non-condensing Initial Set Accuracy Single output models: 1% Multi-output models: 5% Storage Temperature -40 C to +85 C Minimum Load 10% required on V1 & V2 of multi-output models to maintain regulation, unit will start up with no load EMC & Safety Start Up Delay 2 s typical Emissions EN55022, level B conducted and radiated Hold Up Time 12 ms min at 110 VAC, 100% load Harmonic Currents EN61000-3-2, Class A Line Regulation 1% from low line to high line Voltage Flicker EN61000-3-3 Load Regulation 7% max all models 3% typical, see table ESD Immunity EN61000-4-2, level 2 contact, level 3 air, 10% with no load on V1, for multi output Perf Criteria A models Radiated Immunity EN61000-4-3, level 2, Perf Criteria A Transient Response 4% max deviation, recovery to within EFT/Burst EN61000-4-4, level 2, Perf Criteria A 1% in 4 ms for a 50% load change Surge EN61000-4-5, installation Class 3, Ripple & Noise 1% pk-pk typical, 20 MHz bandwidth Perf Criteria A Overvoltage Protection 112-132% of nominal output voltage on Conducted Immunity EN61000-4-6, level 2, Perf Criteria A V1 only, recycle input to reset Magnetic Field EN61000-4-8, 1 A/m, Perf Criteria A Overload Protection 110-150% of nominal power, with auto recovery Dips & Interruptions EN61000-4-11, 30% 10 ms, 60% 100 ms, 100% 5000 ms Short Circuit Protection Trip & restart (hiccup mode), Perf Criteria A, B, B auto recovery Safety Approvals EN60950-1, UL60950-1, Temperature 0.04%/C CSA60950-1 per cUL Coefficient AC DCAC DC SDS60 Models and Ratings Factory-Set (5,6) Output Power Output Voltage Output Current Current Range Total Regulation Model Number (1) Voltage Range 50 W 3.3 V 15.1 A 3.0-5.0 VDC 16.6-10.0 A 5% SDS60US03 55 W 5.0 V 11.0 A 5.0-6.0 VDC 11.0-9.1 A 5% SDS60US05 60 W 7.0 V 8.6 A 6.0-8.0 VDC 10.0-7.5 A 4% SDS60US07 63 W 9.0 V 7.0 A 8.0-11.0 VDC 7.8-5.7 A 3% SDS60US09 63 W 12.0 V 5.2 A 11.0-13.0 VDC 5.7-4.8 A 3% SDS60US12 63 W 15.0 V 4.2 A 13.0-16.0 VDC 4.8-3.9 A 3% SDS60US15 63 W 19.0 V 3.3 A 16.0-21.0 VDC 3.9-3.0 A 3% SDS60US19 63 W 24.0 V 2.6 A 21.0-27.0 VDC 3.0-2.3 A 2% SDS60US24 63 W 30.0 V 2.1 A 27.0-33.0 VDC 2.3-1.9 A 2% SDS60US30 63 W 36.0 V 1.7 A 33.0-40.0 VDC 1.9-1.5 A 2% SDS60US36 63 W 48.0 V 1.3 A 40.0-50.0 VDC 1.5-1.2 A 2% SDS60US48 (2,3,4) (2,3,4) (3) (3) (5,6) Output Power Output V1 Output V2 Output V3 Output V4 Model Number 63.0 W +5.0 V/7.0 A +12.0 V/3.0 A SDS60UD01 48.1 W +3.3 V/7.0 A +5.0 V/5.0 A SDS60UD04 63.0 W +3.3 V/6.0 A +12.0 V/3.0 A -12.0 V/0.8 A SDS60UT00 63.0 W +3.3 V/6.0 A +12.0 V/3.0 A -5.0 V/0.8 A SDS60UT01 63.0 W +3.3 V/6.0 A +12.0 V/3.0 A +5.0 V/0.8 A SDS60UT02 53.5 W +3.3 V/5.0 A +5.0 V/5.0 A +12.0 V/1.0 A SDS60UT03 53.5 W +3.3 V/5.0 A +5.0 V/5.0 A -12.0 V/1.0 A SDS60UT04 63.0 W +5.0 V/6.0 A +12.0 V/3.0 A -12.0 V/0.8 A SDS60UT05 63.0 W +5.0 V/6.0 A +12.0 V/3.0 A -5.0 V/0.8 A SDS60UT06 63.0 W +5.0 V/6.0 A +15.0 V/3.0 A -15.0 V/0.8 A SDS60UT07 63.0 W +5.0 V/6.0 A +24.0 V/2.0 A -24.0 V/0.5 A SDS60UT08 63.0 W +5.0 V/6.0 A +24.0 V/2.0 A -12.0 V/0.8 A SDS60UT09 63.0 W +5.0 V/6.0 A +24.0 V/2.0 A +12.0 V/0.8 A SDS60UT10 63.0 W +3.3 V/6.0 A +12.0 V/3.0 A -12.0 V/0.8 A -5.0 V/0.8 A SDS60UQ00 63.0 W +3.3 V/6.0 A +12.0 V/3.0 A -12.0 V/0.8 A +5.0 V/0.8 A SDS60UQ01 63.0 W +5.0 V/6.0 A +12.0 V/3.0 A -12.0 V/0.8 A -5.0 V/0.8 A SDS60UQ02 63.0 W +5.0 V/6.0 A +12.0 V/3.0 A -12.0 V/0.8 A +24.0 V/0.8 A SDS60UQ03 63.0 W +5.0 V/6.0 A +12.0 V/3.0 A -12.0 V/0.8 A -24.0 V/0.8 A SDS60UQ04 63.0 W +5.0 V/6.0 A +15.0 V/3.0 A -15.0 V/0.8 A -5.0 V/0.8 A SDS60UQ05 59.3 W +5.0 V/6.0 A +24.0 V/1.8 A -15.0 V/0.1 A +12.0 V/0.8 A SDS60UQ06 Notes 1. If an output voltage within the factory-set voltage range is required, a model 4. On multi-output units V2 tracks V1, if V1 is adjusted by 5%, V2 changes by 5%. number will be allocated at the time of order. 5. For optional U-bracket, add suffix B to model number. 2. 10% minimum load required on V1 & V2 of multi-output units to maintain 6. For optional 2 pin AC input, contact sales for details. regulation of 5%. Regulation increases to 10% with no load. 7. To receive unit with cover fitted, add suffix -C to model number. 3. Other output combinations are available - contact sales for more information. Mechanical Details PIN CONNECTIONS 0.16 (4.0) DIA MOUNTING HOLE (4PL.) Pin Single Output Dual Output Triple Output Quad Output 0.22 (5.6) 1 Output 1 Output 2 Output 2 Output 2 2 Output 1 Output 1 Output 1 Output 1 ADJ 3 Output 1 Output 1 Output 1 Output 1 DC OK 4 Return Common Common Common LED 5 Return Common Common Common P2 1 DC 6 Return N/C Output 3 Output 3 AC OUTPUT 7 Output 4 INPUT P1 8 Output 4 6 L (multi output only) 7 8 N Notes G 1. All dimensions are in inches (mm) 2. Weight: 0.52 lbs (240 g) approx 3. Tolerance: 0.02 (0.5) 4.56 (115.8) 4. Input connector mates with Molex housing 09-50-3051 and Molex 2878 series crimp terminal. 0.22 (5.6) 5.00 (127.0) 5. Output connector mates with Molex housing 09-50-3061 or 9-50-3081 and Molex 2878 series crimp terminal. 6. For optional cover kit order part number SDS60 COVER KIT, to receive unit with cover fitted add suffix -C to model number. Cover size: 5.46 x 3.55 x 1.55 (140 x 91 x 39.7mm). 7. For mating connectors and cable harness order part numbers: SDS60 CON KIT - Single, dual and triple output models SDS60Q CON KIT - Quad output models 0.12 (3.0) SDS60 LOOM KIT - Single output models cable harness max SDS60DT LOOM KT - Dual and triple output models cable harness SDS60Q LOOM KIT - Quad output models cable harness 21-Jan-11 2.55 (64.8) 1.20 (30.5) 3.00 (76.2)