VR10S09 XP Power

DC-DC Converter VR10 Series 1.0 Amp Non Isolated 1.0A Switching Regulator xxx Series Regulated Single Outputs from 3.3 to 15VDC Wide Input Range to 36V SIP3 Package High Efficiency to 96% Class B Conducted & Radiated Emissions Short Circuit Protection Low 0.3mA Standby Input Current -40C to +85C Operation MTBF >2MHrs 3 Year Warranty Dimensions: The VR10 provides a cost effective compact efficient switching regulator solution operating VR10: 0.457 x 0.409 x 0.315 (11.6 x 10.4 x 8.0mm) from a wide range DC input. Output voltages start from 3.3V and the VR10 consumes as little as 0.3mA when idle. Models & Ratings (1) (2) Input Current Efficiency Max. Capacitive Input Voltage Output Voltage Output Current Model Number Load No Load Full Load Vin, Min. Vin, Max. 6-36V 3.3V 1.0A 1.0mA 660mA 680F 90% 80% VR10S3V3 8-36V 5.0V 1.0A 0.3mA 720mA 680F 93% 85% VR10S05 10-36V 6.5V 1.0A 0.3mA 740mA 680F 93% 85% VR10S6V5 13-36V 9.0V 1.0A 0.3mA 760mA 680F 94% 89% VR10S09 16-36V 12.0V 1.0A 0.3mA 810mA 680F 95% 92% VR10S12 20-36V 15.0V 1.0A 0.3mA 802mA 680F 96% 93% VR10S15 Notes 1. Full load input current measured at minimum input voltage. 3. Standard tube quantity 43 pcs. 2. Efficiency measured at full load. Mechanical Details FRONT VIEW UNDERSIDE VIEW FOOTPRINT (TOP VIEW) 0.091 (2.30) 0.028 (0.70) Pin Connections 0.039 ( 1.00) 1 2 3 1 2 3 Pin Single 0.012 (0.30) 1 +Vin 2 Ground 0.100 (2.54) 3 +Vout 0.457 (11.60) TYP. 0.200 (5.08) 0.161 (4.10) 0.200 (5.08) Notes 1. All dimensions are in inches (mm) 4. Case & pin tolerance: 0.02 (0.5) 2. Weight: 0.0041lbs (1.9g) approx. 3. Pin diameter: 0.020.004 (0.70.1) www.xppower.com 1 0.020 (0.50) 0.409 (10.40) 0.315 (8.00)DC-DC Converter VR10 Series Input Characteristic Minimum Typical Maximum Units Notes & Conditions Input Voltage Range 6 36 VDC See Models and Ratings table. Input Filter Internal capacitor Input Reflected Ripple 20 mA pk-pk Input Surge 45 VDC For max. 100ms. Output Characteristic Minimum Typical Maximum Units Notes & Conditions Output Voltage 3.3 15 VDC See Models and Ratings table. Initial Set Accuracy 2.0 4.0/3.0 % 3.3V/others (At full load). Minimum Load 0 mA No minimum load required. Line Regulation 0.2 0.4 % Full load over input voltage range. Load Regulation 0.4 0.6 % Maximum variation applies to 3.3V output models. Transient Response 1 % For 50% load change. Recovery in 100s. Ripple & Noise 75 mV pk-pk 20 MHz bandwidth. Short Circuit Protection Continuous, with auto recovery. Maximum Capacitive Load See Models and Ratings table. Temperature Coefficient 0.03 %/ C Overload Protection 2.2 A Start-up Time 20 ms General Characteristic Minimum Typical Maximum Units Notes & Conditions Efficiency 93 % See models and ratings table. Isolation: Input to Output 0 VDC Non isolated. Switching Frequency 520 kHz At full load. Mean Time Between Failure 2 MHrs MIL-HDBK-217F. Weight 0.0041 (1.9) lb (g) Case Material Non-conductive black plastic UL94V-0. Pin Material Solder coated phosphor bronze C5191R-1/2H. Potting Material Polyurethane type L780 UL94V-0 rated. Water Wash Use de-ionised water only, dry thoroughly. Wave solder peak, 1.5mm from case 10s max. Not suitable Soldering Temperature 260 C for vapour phase soldering. For further details contact XP Power applications team. Environmental Characteristic Minimum Typical Maximum Units Notes & Conditions Operating Temperature -40 +85 C See derating curves. Storage Temperature -55 +125 C Case Temperature +120 C Humidity 95 %RH Non-condensing. Cooling Natural convection. www.xppower.com 2