Through-hole resisT ors High Power Type Wirewound Resistors Ultra Miniature Style PNP Series FeATures Power Rating 1W, 2W, 3W, 4W Resistance Tolerance 1%, 5% T.C.R. 300ppm/C Flameproof Multi-layer Coating Meets UL-94V-0 Flameproof Feature Meets Overload Test UL-1412 iNTroDuCTioN DerATiNg Cur Ve The resistor element is a resistive wire which For resistors operated in ambient temperatures above 70C, power rating must be derated is wound in a single layer on a ceramic rod, in accordance with the curve below. with tinned connecting wires of electrolytic 70 200 275 C copper welded to the end-caps. The ends of Rated Load (%) 100 the resistive wire are connected to the caps by 80 welding. The resistors are coated with layers of 60 green color flame-proof lacquer. High power in 40 small packages. 20 Ambient Temperature (C) 50 100 150 200 250 300 DiMeNsioNs Unit: mm s TYle DiMeNsio N u ltra Miniature l D h d d PNP100 6.30.5 2.50.3 282.0 0.550.05 H L D PNP200 9.00.5 3.50.3 262.0 0.550.05 PNP300 11.51.0 4.60.5 352.0 0.80.05 5th color code: violet PNP400 15.51.0 5.20.5 332.0 0.80.0555 Note: High Power Type Ultra Miniature Style PNP Series eleCTriCAl ChArACTerisTiCs s TYle PNP100 PNP200 PNP300 PNP400 Power Rating at 70C 1W 2W 3W 4W Maximum working voltage PxR Voltage Proof on Insulation 300V Resistance Range (1%) 0.22 - 130 0.1 - 820 0.1 - 2.2K 0.1 - 2.8K Resistance Range (5%) 0.1 - 130 0.1 - 820 0.1 - 2.2K 0.1 - 2.8K Operating Temp. Range -40C to +200C Temperature Coefficient 300ppm/C Note: Special value is available on request eNViroNMeNTAl ChArACTerisTiCs Per For MANCe Tes T Tes T MeTho D APPr Aise Shor t Time Overload IEC 60115-1 4.13 10 times rated power for 5 Sec. 2.0%+0.05 Voltage Proof on Insulation IEC 60115-1 4.7 in V-block for 60 Sec., test voltage by type By type Temperature Coefficient IEC 60115-1 4.8 -55C to +155C By type Insulation Resistance IEC 60115-1 4.6 in V-block for 60 Sec. >100M Solderability IEC 60115-1 4.17 2355C for 30.5 Sec. 95% Min. coverage No deterioration of Solvent Resistance of Marking IEC 60115-1 4.30 IPA for 50.5 Min. with ultrasonic coatings and markings Robustness of Terminations IEC 60115-1 4.16 Direct load for 10 Sec. in the direction of the terminal leads 2.5kg (24.5N) Damp Heat Steady State IEC 60115-1 4.24 402C, 90-95% RH for 56 days, loaded with 0.1 times RCWV 5.0%+0.05 Endurance at 70C IEC 60115-1 4.25 702C at RCWV for 1,000 Hr. (1.5 Hr. on, 0.5 Hr. off) 5.0%+0.05 Temperature Cycling IEC 60115-1 4.19 -55C Room Temp. +155C Room Temp. (5 cycles) 1.0%+0.05 Resistance to Soldering Heat IEC 60115-1 4.18 2603C for 101 Sec., immersed to a point 30.5mm from the body 1.0%+0.05 No evidence of flaming Accidental Overload Test IEC 60115-1 4.26 4 times RCWV for 1 Min. or arcing Note: RCWV(Rated Continuous Working Voltage) = Power Rating x Resistance Value or Max. working voltage listed above, whichever less. Revision: 201304