CENTRAL RADIO ROLLER BLINDS CONTROLLER SRP-03 MANUAL INSTRUCTION ZAMEL Sp. z o.o. ul. Zielona 27, 43-200 Pszczyna, Poland tel. +48 (32) 210 46 65, fax +48 (32) 210 80 04 www.zamelcet.com, e-mail: marketing zamel.pl DESCRIPTION TECHNICAL DATA Radio roller blinds controller SRP-03 is SRP-03 used to realise central control function of Input (supply) terminals: L, N roller blind drives. The device generates Input rated voltage: 230V AC central control impulses (full opening or Input voltage tolerance: -15 +10 % closing of a single roller blind or a group Nominal frequency: 50 / 60 Hz of roller blinds, the impulse is 0,5 second Nominal power consumption: 0,4 W (stand-by mode) / 0,7 W (operation mode) long). SRP-03 device can be used as an Transmission: radio 868,32 MHz element of wireless (EXTA FREE system Coding way: unidirectional transmitters) or wired (roller blind switch- Coding: addressing transmission es) central control - which allows for in- Maximum number of transmitters: 32 tegration of wired roller blinds switches Range: up to 250 m in the open area (SRM-10, SRP-01 or devices of different Optic signalling of transmitter s operation: LED red diode manufacturers) with wireless EXTA FREE control system. Control terminals: LOCAL/CENTRAL (up), (down) Roller blind motor power supply terminals: OUT (up), (down) Relay contact parameters: 2NO 5A / 250V~ AC1 1250 VA (voltage contacts) FEATURES Number of terminal clamps: 6 2 used in wired and wireless central (group) Section of connecting cables: 0,2 2,50 mm control of roller blind, sunblind and gate o Ambient temperature range: -10 +55 C drives, (electric motors of 230V AC), Operating position: free inputs of wired roller blind central control, Casing mounting: installation cable box 60 mm integration with wired roller blind switches Casing protection degree: IP20 (EN 60529) SRM-10 and SRP-01 or devices of differ- Protection level: II ent manufacturers, Overvoltage category: II energy-saving device, possibility of con- Pollution degree: 2 stant work, Surge voltage: 1 kV (EN 61000-4-5) possibility of cooperation with any roller Dimensions: 47,5 x 47,5 x 20 mm blind switch (which is not equipped in Weight: 0,039 kg backlight elements), Reference standard: EN 60669, EN 60950, EN 61000 T he d ev i c e i s de s i g ne d f o r s i n- APPEARANCE g l e - p h as e i ns t a ll a t i o n an d mus t b e i ns t a ll e d i n a c c o r da nc e w i t h s t a n da r ds va l i d i n a pa r t i c ul a r c o u n t r y. T h e d e v i c e s h o u l d b e Central wired control terminals c o n n e c t e d a c c o r d i n g t o t h e CAUTION (upward movement , downward movement ) d e t ai l s in c lu d e d i n t hi s o p e r a t i n g m an ua l . I ns t a l- l a t i o n , c o n n e c t i o n a n d c o n t r o l s h o u l d b e c a r r i e d Signal control output terminals o u t b y a q u a l i fi e d e l e c t r i c i a n s t a f f, w h o a c t i n a c- (upward movement , downward movement ) c o r d a n c e w i t h t h e s e r v i c e m a n u a l a n d t h e d e v i c e f u nc t i o ns . Input (supply) terminals (L, N) I n c a s e o f c a s i n g d i s m a n t l i n g a n e l e c t r i c s h o c k m a y o c c u r, a n d t h e g u a r a n t e e i s l o s t t h e n . B e f o r e i n s t a l l a t i o n m a ke s u r e t h e c o n n e c t i o n c a b l e s a r e n o t u n d e r v o l t a g e . T h e c r u c i f o r m h e a d s c r e w- d r i v e r 3 , 5 m m s h o u l d b e u s e d t o i n s t a l t h e d e v i c e . I m p r o p e r t r a n s p o r t , s t o r a g e , a n d u s e o f t h e d e v i c e Optic signalling of receiver s operation i n fl u e n c e i t s w r o n g f u n c t i o n i n g . I t i s n o t a d v i s a b l e t o i n s t a l t h e d e v i c e i n t h e f o l l o w i n g c a s e s : i f a ny Programming push-button d e v i c e p a r t i s m i s s i n g o r t h e d e v i c e i s d a m a g e d o r d e f o r m e d . I n c a s e o f i m p r o p e r f u n c t i o n i n g o f t h e d e v i c e c o n t a c t t h e p r o d u c e r. The ZAMEL company devices The symbol means selective which are characterised collecting of electrical and electronic with this sign can cooperate equipment. with each other It is forbidden to put the used equipment together with other waste VER. 003 19.05.2011CONNECTION MOUNTING 1. Disconnect power supply by the phase fuse, the circuit-breaker or the switch- LOCAL CENTRAL disconnector combined to the proper circuit. 2. Check if there is no voltage on con- nection cables by means of a special measure equipment. 3. Connect the cables with the terminals in accordance with the installing diagram. 4. Install SRP-03 device in installation ca- ble box. 5. Switch on the power supply from the mains. Caution: connection of wired switches (LOCAL/CENTRAL) is optional. RADIO TRANSMITTERS PROGRAMMING Press PROG push-button of SRP-03 device Press and release transmitter s first Press and release the second transmitter s for a longer time until LED red diode switches on push-button (movement ). LED red push-button (movement ). LED red diode (constant signal). Next release PROG push-button. diode switches on (first signal pulsates, switches on (signal pulsates) and then switches next the signal is constant). off - THE TRANSMITTER IS ADDED. An exemplary programming procedure of P-257/2 remote control. The procedure for the rest of radio EXTA FREE transmitters is analogous. RADIO TRANSMITTERS DELETION Press PROG push-button of SRP-03 After 5 seconds LED red diode switches on Release the push-button in SRP-03 - device for a longer time. (signal pulsates) and then it switches off. MEMORY IS DELETED. APPLICATION OPERATION RANGE Transmitter SRP-03 Transmitter SRP-03 Roller blinds control system realised by means of wired roller blind controllers RNK-02 200 m RNP-02 180 m SRP-01. One controller can be used for RNK-04 200 m RNL-01 brak* one roller blind. Each of the controllers P-256/8 250 m RTN-01 200 m has a local control push-button and connected inputs of central control, P-257/4 (2) 200 m RCR-01 brak* which allow to close or open a given RNM-10 250 m RTI-01 180 m group of roller blinds by means of SRP-03 device - central roller blinds RNP-01 180 m RXM-01 250 m controller. SRP-03 is operated in a * 1-channel transmitters do not cooperate wireless way by means of 8-channel with roller blind controllers. remote control P-256/8. Roller blinds CAUTION: The given range concerns open area - an switches can not be equipped with ideal condition without any natural or artificial obsta- backlight. cles. If there are some obstacles between a trans- mitter and a receiver, it is advisable to decrease the range according to: wood and plaster: from 5 to 20 %, bricks: from 10 to 40 %, reinforced concrete: from 40 to 80 %, metal: from 90 to 100% , glass: from 10 to 20 %, Over- and underground medium and high elec- trical power lines, radio and television transmitters, GSM transmitters set close to a device system have also a negative influence on the range. WARRANTY CARD There is 24 months guarantee on the product 1. ZAMEL provides a two-year warranty for its products. 2. The ZAMEL warranty does not cover: a) mechanical defects resulting from transport, loading / unloading or other circumstances b) defects resulting from incorrect installation or operation of ZAMEL products c) defects resulting from any changes made by CUS- TOMERS or third parties, to products sold or equipment necessary for the correct operation of products sold d) defects resulting from force majeure or other aleatory events for which ZAMEL is not liable e) power supply (batteries) to be equipped with a device in the moment of sale (if they appear) 3. All complaints in relation to the warranty must be provided by the CUSTOMER in writing to the retailer after discovering a defect. 4. ZAMEL will review complaints in accordance with existing regulations. 5. The way a complaint is settled, e.g. replacement of the product, repair or refund, is left to the discretion of ZAMEL. 6. Guarantee does not exclude, does not limit, nor does it suspend the rights of the PURCHASER resulting from the discrepancy between the goods and the contract. Salesman stamp and signature, date of sale