PLF1C471MDO1TD Nichicon

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS Radial Lead Type, Standard PLF Low ESR, High ripple current. Load life of 2000 hours at 105C. Radial lead type : PLG Lead free flow soldering condition correspondence. Compliant to the RoHS directive (2011/65/EU,(EU)2015/863). Higher Capacitance AEC-Q200 compliant. Please contact us for details. Long Life Low ESR PLS PLE PLF Specifications Item Performance Characteristics Category Temperature Range 55 to +105C Rated Voltage Range 2.5 to 25V Rated Capacitance Range 6.8 to 1500F Capacitance Tolerance 20% at 120Hz, 20C Tangent of loss angle (tan ) Less than or equal to the specified value 120Hz, 20C at ESR ( 1) Less than or equal to the specified value at 100kHz, 20C Leakage Current ( 2) Less than or equal to the specified value. After 2 minutes application of rated voltage at 20C Temperature Characteristics Z+105C / Z+20C 1.25 (100kHz) (Max.Impedance Ratio) Z55C / Z+20C 1.25 Capacitance change Within 20% of the initial capacitance value ( 3) The specifications listed at right shall be met when the 150% or less than the initial specified value tan Endurance capacitors are restored to 20C after the rated voltage is ( 1) ESR 150% or less than the initial specified value applied for 2000 hours at 105C. Leakage current ( 2) Less than or equal to the initial specified value ( ) Capacitance change Within 20% of the initial capacitance value 3 The specifications listed at right shall be met when the Damp Heat tan 150% or less than the initial specified value capacitors are restored to 20C after the rated voltage is ESR ( 1) 150% or less than the initial specified value (Steady State) applied for 1000 hours at 60C, 90% RH. Leakage current ( 2) Less than or equal to the initial specified value After soldering the capacitor under the soldering conditions ( ) Capacitance change Within 10% of the initial capacitance value 3 prescribed here as preheat at 150 to 200C for 60 to 180 seconds tan 130% or less than the initial specified value Resistance to and peak temperature at 265C for 10 seconds or less, the ESR ( 1) 130% or less than the initial specified value capacitor shall meet the specifications listed at right, provided that Soldering Heat Leakage current ( 2) Less than or equal to the initial specified value its temperature profile is measured at both of terminal ends facing the soldering side. Marking Navy blue print on the case top 1 ESR should be measured at both of the terminal ends closest to the capacitor body. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120 minutes at 105C. 3 Initial value : The value before test of examination of resistance to soldering. Dimensions Type numbering system (Example : 4V 560 F) Capacitance Resin coated Case 1 2 3 4 5 6 7 8 9 10 11 12 Voltage(g:4V) P L F 0 G 5 6 1 M D O 1 Size code Configuration d Capacitance tolerance (20%) Series Lot. No. Rated capacitance (560F) +0.5MAX. L 15MIN 4MIN Rated voltage (4V) Series name Type (mm) Voltage Size 6.3 6L 6.3 9L 6.3 10.5L 8 7L 8 9L 8 12L 10 8L 10 10L 10 13L V 2.5 4 6.3 10 16 20 25 6.3 6.3 6.3 8.0 8.0 8.0 10.0 10.0 10.0 D Code e g j A C D E 5.5 8.5 10.0 6.5 8.5 11.5 7.5 9.5 12.5 L 2.5 2.5 2.5 3.5 3.5 3.5 5.0 5.0 5.0 P Frequency coefficient of rated ripple current 0.45 0.6 0.5 0.6 0.6 0.6 0.6 0.6 0.6 d 0 Frequency0/ 120Hz 1kHz 10kHz 100kHz or more Coefficient 0.05 0.30 0.70 1.00 Please refer to page 20 about the end seal configuration. Dimension table in next page. 62 L F 5 6 0 g 8 4 1 D0.5 0.5 PCONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS PLF Dimensions Rated Voltage ESR Rated Ripple Surge Voltage Rated Capacitance Case Size Leakage Current (V) (m) (mArms) tan Part Number (V) (F) D L (mm) (A) (at 100kHz 20C) (105C/100kHz) (code) 330 6.3 9 0.08 500 7 5600 PLF0E331MCO8 390 6.3 10.5 0.08 195 20 3200 PLF0E391MDL4 560 6.3 9 0.08 500 7 5600 PLF0E561MCO8 560 8 9 0.08 280 6 4800 PLF0E561MCO1 680 8 9 0.08 340 7 4800 PLF0E681MCO6 680 8 12 0.08 340 6 5700 PLF0E681MDO1 2.5 2.8 820 6.3 9 0.08 500 7 5600 PLF0E821MCO8 (0E) 820 8 9 0.08 410 7 5200 PLF0E821MCO6 820 8 12 0.08 410 6 6200 PLF0E821MDO1 1000 10 13 0.08 500 6 6500 PLF0E102MDO1 1200 10 13 0.08 600 8 5300 PLF0E122MDO1 8 12 0.08 7 6100 PLF0E152MDO6 1500 750 1500 10 13 0.08 750 8 5500 PLF0E152MDO1 270 6.3 9 0.08 500 7 5600 PLF0G271MCO8 6.3 10.5 0.08 PLF0G271MDL4 270 216 20 3200 390 6.3 10.5 0.08 312 24 3300 PLF0G391MDL4 560 8 9 0.08 448 7 5200 PLF0G561MCO6 4 8 12 4.6 560 0.08 448 7 5500 PLF0G561MDO1 (0G) 680 8 12 0.08 544 6 6200 PLF0G681MDO1 820 10 13 0.08 656 6 6500 PLF0G821MDO1 10 13 1000 0.08 800 6 6640 PLF0G102MDO1 1200 10 13 0.08 960 8 5600 PLF0G122MDO1 220 6.3 10.5 0.08 277 20 3200 PLF0J221MDL4 6.3 10.5 330 0.08 416 24 3300 PLF0J331MDL4 6.3 470 8 9 0.08 592 7 5200 PLF0J471MCO6 7.2 (0J) 470 8 12 0.08 592 7 5500 PLF0J471MDO1 10 13 680 0.08 857 6 6300 PLF0J681MDO1 47 6.3 10.5 0.08 94 25 2900 PLF1A470MDL4 68 6.3 10.5 0.08 136 25 2900 PLF1A680MDL4 100 6.3 10.5 0.08 200 25 2900 PLF1A101MDL4 150 6.3 10.5 0.08 300 25 2900 PLF1A151MDL4 10 11.5 270 8 12 0.08 540 8 4900 PLF1A271MDO1 (1A) 470 10 13 0.08 940 7 5700 PLF1A471MDO1 560 10 13 0.08 1120 7 5900 PLF1A561MDO1 680 10 13 0.08 1360 7 6100 PLF1A681MDO1 100 6.3 10.5 0.08 320 24 2900 PLF1C101MDL4 180 8 12 0.08 576 9 5000 PLF1C181MDO1 16 270 8 12 0.08 864 9 5100 PLF1C271MDO1 18.4 (1C) 330 10 13 0.08 1056 9 6100 PLF1C331MDO1 470 10 13 0.08 1504 9 6100 PLF1C471MDO1 22 6.3 6 0.12 88 50 1700 PLF1D220MCL2 39 8 7 0.12 156 45 2000 PLF1D390MCL2 47 8 7 0.12 188 45 2000 PLF1D470MCL2 56 10 8 0.12 224 40 2400 PLF1D560MCL2 20 68 10 8 0.12 272 40 2600 PLF1D680MCL2 23 (1D) 82 10 8 0.12 328 40 2600 PLF1D820MCL2 100 8 12 0.12 400 22 3320 PLF1D101MDO2 120 10 10 0.12 480 35 2800 PLF1D121MCL2 150 10 13 0.12 600 20 4320 PLF1D151MDO2 6.8 6.3 6 0.12 85 80 1200 PLF1E6R8MCL2 10 6.3 6 0.12 125 65 1500 PLF1E100MCL7 10 8 7 0.12 125 60 1500 PLF1E100MCL2 25 28.7 (1E) 22 8 7 0.12 275 50 1800 PLF1E220MCL7 47 10 13 0.12 588 30 3000 PLF1E470MDO2 56 10 13 0.12 700 28 3800 PLF1E560MDO2 Rated ripple current (mArms) at 105C 100kHz No marked, 1 will be put at 12th digit of type numbering system. : In this case, 2 will be put at 12th digit of type numbering system. Please refer to page 20, 21, 22 about the formed or taped product spec. : In this case, 4 will be put at 12th digit of type numbering system. Please refer to page 3 for the minimum order quantity. : In this case, 6 will be put at 12th digit of type numbering system. 63 : In this case, 7 will be put at 12th digit of type numbering system. : In this case, 8 will be put at 12th digit of type numbering system.