TYPE NUMBER PRODUCT SPECIFICATION GS-12-285 TITLE PAGE REVISION 1 of 7 A AUTHORIZED BY DATE EXPRESSCARD CONNECTOR PRODUCT SPECIFICATION KENNY TAI 11/05/03 CLASSIFICATION UNRESTRICTED 1. OBJECTIVE This specification defines the performance, test, quality and reliability requirements of ExpressCard connectors. 2. SCOPE This specification provides information regarding product features and materials for ExpressCard connectors. All products shall meet ExpressCard Standard, PCMCIA /JEITA. 3. GENERAL This document is composed of the following sections: Paragraph Title 1.0 OBJECTIVE 2.0 SCOPE 3.0 GENERAL 4.0 APPLICABLE DOCUMENTS 4.1 STANDARD AND SPECIFICATIONS 5.0 REQUIREMENTS 5.1 MATERIAL 5.2 FINISH 6.0 CONNECTOR REQUIREMENTS 6.1 EXAMINATION OF PRODUCT 6.2 MATING / UNMATING FORCE 6.3 SOLIDERABILITY 6.4 ELECTRICAL REQUIREMENTS 6.5 DURABILITY TEST REQIREMENTS 7.0 TEST SEQUENCE 8.0 RECOMMENDED TEMPERATURE PROFILE 9.0 NOTE 4. APPLICATION DOCUMENTS 4.1 Standards and Specifications 4.1.1 EIA-364-1000.01, Electrical / Socket Test Procedures Including Environmental Classifications 4.1.2 ExpressCard Standard 4.1.3 FCI product drawings 5. REQUIREMENT 5.1 Material 5.1.1 Terminal The terminal material shall be copper alloy and specified in the product drawing. 5.1.2 Housing The housing material shall be rated UL94V-0 and shall be specified in the product drawing. 5.2 Finish The finish for applicable components shall be specified in product drawings with plating area, plating material and plating thickness. 6. CONNECTOR REQUIREMENTS 6.1 Examination of Product Samples must comply to applicable FCI product prints. 6.2 Mating / Unmating force This document is the property of and embodies CONFIDENTIAL and PROPRIETARY information of FCI Electronics. No part of the information shown on this document may be used in any way without the written consent of FCI Electronics. Form E-3005 GS-01-001 Rev A 02/12/01 V20603 PDM: Rev:B Released .STATUS: Printed: Nov 28, 2010TYPE NUMBER PRODUCT SPECIFICATION GS-12-285 TITLE PAGE REVISION 2 of 7 A AUTHORIZED BY DATE EXPRESSCARD CONNECTOR PRODUCT SPECIFICATION KENNY TAI 11/05/03 CLASSIFICATION UNRESTRICTED Table 6-1 Mating / Unmating force Test Description Procedure Requirements EIA 364-13 Measure the force to mate the dummy card for module side and, with guiding plates and Insertion Force 39N maximum. mechanism assemblies in host side at a maximum rate of 12.5 mm (0.492 inches) per minute. EIA 364-13 Measure the force to un-mate the dummy card for module side and, with guiding plates and 3.7N min. 18.5N Removal Force mechanism assemblies in host side at a max. maximum rate of 12.5 mm (0.492 inches) per minute. 6.3 Solderability: Per EIA-364-638 Steam age for 1 hour. Contact areas evaluated shall meet 95% minimum coverage. 6.4 Electrical Requirements Unless otherwise specified, all test and measurements shall be made at: Temperature 25C +/- 5C Relative humidity 50% Max Table 6-2 lists ExpressCard connector electrical test procedure and requirements. Table 6-2 ExpressCard connector electrical requirements Item Paramater Procedure Requirements Initial: 40 m max Final (after stress): 55 m Contact Resistance 6-4-1 EIA 364-23B max (allowable resistance (LLCR) change: 15m ) Initial 1000 M min. 6-4-2 Insulation Resistance EIA-364-21, 500V DC After test 100 M min. 1. No shorting or other Dielectric withstanding EIA 364-20 damages. 6-4-3 voltage 500Vrms AC for 1 minute 2. Current leakage 1 mA max This document is the property of and embodies CONFIDENTIAL and PROPRIETARY information of FCI Electronics. No part of the information shown on this document may be used in any way without the written consent of FCI Electronics. Form E-3005 GS-01-001 Rev A 02/12/01 V20603 PDM: Rev:B Released .STATUS: Printed: Nov 28, 2010