Click here to ask about the production status of specific part numbers. MAX20336/MAX20337 Ultra-Small, Low-R , Beyond-the-Rails ON DPST/SPDT Analog Switches General Description Benefits and Features The MAX20336/MAX20337 ultra-small, low-on-resistance Distortion-Free Beyond-the-Rails Signaling (R ) double-pole/single throw (DPST) and single-pole/ Negative Voltage Audio and Video Signal Capable ON double-throw (SPDT) analog switches feature Beyond- -5.5V to +5.5V Analog Signal Range Independent the-Rails capability that allows signals from -5.5V to of V CCEN +5.5V to pass without distortion, even when the power On-Resistance 0.19 (typ) supply is below the signal range. The low on-resistance +1.6V to +5.5V Single-Supply Range (0.19) also makes the devices ideal for low-distortion Total Harmonic Distortion Plus Noise -114dB (typ) switching applications, such as audio or video. On-Resistance Flatness 0.0001 (typ) The MAX20336/MAX20337 are fully specified to operate Low Supply Current 65A/70A (typ) at 1.6V from a single +1.6V to +5.5V power supply. Because of Can be Powered by GPIO the low supply current requirement, V can be provid- High-Impedance Mode when V Not Applied CCEN CCEN ed by a GPIO. When power is not applied, the switches go ESD Protection on COM , NO , NC to a high-impedance mode and all analog signal ports can 30kV Human Body Model withstand signals from -5.5V to +5.5V. 7kV IEC 61000-4-2 Air Gap The MAX20336/MAX20337 are available in a 1.308mm 8kV IEC 61000-4-2 Contact x 0.828mm, 0.4mm pitch, 6-bump wafer-level package Design Flexibility (WLP) and 1.25mm x 1.75mm 6-pin FC2QFN package, 6-Bump WLP (1.308mm x 0.828mm) Package and operate over the -40C to +85C extended tempera- 6-Pin FC2QFN (1.25mm x 1.75mm) Package ture range. -40C to +85C Operating Temperature Range Applications Ordering Information appears at end of data sheet. Cell phone Tablet Portable Audio/Video Equipment Portable Navigation Devices Simplified Block Diagram V V CCEN CCEN MAX20337MAX20337 MAX20336MAX20336 CONTROL CB NO1 COM1 NO COM NO2 COM2 NC Beyond-the-Rails is a trademark of Maxim Integrated Products, Inc. 19-100482 Rev 1 1/21MAX20336/MAX20337 Ultra-Small, Low-R , Beyond-the-Rails ON DPST/SPDT Analog Switches Absolute Maximum Ratings V , CB to GND .................................................. -0.3V to +6V FC2QFN (derate 5.83mW/C above +70C)..................466.2mW CCEN NO , COM , NC to GND............................................. -6V to +6V Operating Temperature Range.............................-40C to +85C Continuous Current NO , COM , NC ............................. 500mA Junction Temperature.......................................................+150C Peak Current NO , COM , NC Storage Temperature Range ..............................-65C to +150C (50% duty cycle, 10ms pulse)...................................... 850mA Soldering Temperature (reflow) ........................................+260C Continuous Power Dissipation (T = +70C) A WLP (derate 10.51mW/C above +70C) .................. 840.8mW Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Package Information 6 BUMP WLP (MAX20336) Package Code N60K1+1 Outline Number 21-100308 Land Pattern Number Refer to Application Note 1891 THERMAL RESISTANCE, FOUR-LAYER BOARD Junction to Ambient ( ) 95.15C/W JA 6 BUMP WLP (MAX20337) Package Code N60K1+2 Outline Number 21-100311 Land Pattern Number Refer to Application Note 1891 THERMAL RESISTANCE, FOUR-LAYER BOARD Junction to Ambient ( ) 95.15C/W JA 6 FC2QFN (MAX20336/MAX20337) Package Code F61A1F+1 Outline Number 21-100313 Land Pattern Number 90-100167 THERMAL RESISTANCE, FOUR-LAYER BOARD Junction to Ambient ( ) 171.6 C/W JA Junction to Ambient ( ) 58.7 C/W JC For the latest package outline information and land patterns (footprints), go to www.maximintegrated.com/packages. Note that a +, , or - in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a four-layer board. For detailed information on package thermal considerations, refer to www.maximintegrated.com/ thermal-tutorial. www.maximintegrated.com Maxim Integrated 2