EVALUATION KIT AVAILABLE MAX2769B Universal GPS Receiver General Description Features The MAX2769B is a next-generation Global Navigation S AEC-Q100 Automotive Qualified Satellite System (GNSS) receiver covering GPS, GLONASS, S GPS/GLONASS/Galileo/Compass Systems Galileo, and Compass navigation satellite systems on S 40pF Output Clock Drive Capability a single chip. This single-conversion GNSS receiver is S No External IF SAW or Discrete Filters Required designed to provide high performance for industrial and automotive applications. S Programmable IF Frequency Designed on Maxims advanced, low-power SiGe BiCMOS S Fractional-N Synthesizer with Integrated VCO process technology, the MAX2769B offers the highest Supports Wide Range of Reference Frequencies performance and integration at a low cost. Incorporated S Dual-Input Uncommitted LNA for Separate Passive on the chip is the complete receiver chain, including a and Active Antenna Inputs dual-input LNA and mixer, followed by the image-rejected S 1.4dB Cascade Noise Figure filter, PGA, VCO, fractional-N frequency synthesizer, crystal oscillator, and a multibit ADC. The total cascaded S Integrated Crystal Oscillator noise figure of this receiver is as low as 1.4dB. S Integrated Active Antenna Sensor The MAX2769B completely eliminates the need for exter- S 2.7V to 3.3V Supply Voltage nal IF filters by implementing on-chip monolithic filters S Small, 28-Pin, RoHS-Compliant, Thin QFN Lead- and requires only a few external components to form a Free Package (5mm x 5mm) com plete low-cost GPS RF receiver solution. The MAX2769B is the most flexible receiver on the mar- Ordering Information appears at end of data sheet. ket. The integrated delta-sigma fractional-N frequency synthesizer allows programming of the IF frequency within a 30Hz (f = 32MHz) accuracy while operat- XTAL Block Diagram ing with any reference or crystal frequencies that are available in the host system. The ADC outputs CMOS logic levels with 1 or 2 quantized bits for both I and Q channels, or up to 3 quantized bits for the I channel. I and Q analog outputs are also available. 21 20 19 18 17 16 15 The MAX2769B is packaged in a 5mm x 5mm, 28-pin thin N.C. 22 14 V CCD QFN package with an exposed paddle. V 13 V CC IF 23 CC CP Applications MAX2769B Automotive Navigation Systems CPOUT IDLE 24 12 Location-Enabled Mobile Handsets FILTER V LNA2 25 11 CC VCO PNDs (Personal Navigation Devices) VCO LNA2 Telematics (Asset Tracking, Inventory PGM 26 10 CS Management) Marine/Avionics Navigation LNA1 27 9 SCLK LNA1 Software GPS N.C. 28 8 SDATA Laptops and Netbooks + 1 2 3 4 5 6 7 For related parts and recommended products to use with this part, refer to www.maximintegrated.com/MAX2769B.related. For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxims website at www.maximintegrated.com. 19-5875 Rev 2 10/12 ANTFLAG I1 ADC LNAOUT I0 ANTBIAS V CC ADC V Q0 CC RF ADC 0 90 MIXIN Q1 PLL 3-WIRE CLKOUT LD INTERFACE XTAL SHDNMAX2769B Universal GPS Receiver ABSOLUTE MAXIMUM RATINGS V to Ground ....................................................-0.3V to +4.2V Operating Temperature Range .......................... -40NC to +85NC CC Other Pins Except LNA , MIXIN, XTAL, and LNAOUT to Junction Temperature .....................................................+150NC Ground............................. -0.3V to +(Operating V + 0.3V) Storage Temperature Range ............................ -65NC to +150NC CC Lead Temperature (soldering, 10s) ................................+300NC Maximum RF Input Power .............................................+15dBm Soldering Temperature (reflow) ......................................+260NC Continuous Power Dissipation (T = +70NC) A TQFN (derates 27mW/NC above +70NC) ...................2500mW Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional opera- tion of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. CAUTION ESD SENSITIVE DEVICE DC ELECTRICAL CHARACTERISTICS (MAX2769B EV kit, V = 2.7V to 3.3V, T = -40NC to +85NC, PGM = Ground. Registers are set to the default power-up states. Typical CC A values are at V = 2.85V and T = +25NC, unless otherwise noted.) (Note 1) CC A PARAMETER CONDITIONS MIN TYP MAX UNITS Supply Voltage 2.7 2.85 3.3 V Default mode, LNA1 is active (Note 2) 18 27 31 Default mode, LNA2 is active (Note 2) 15 25 30.5 mA Supply Current 5 Idle ModeK, IDLE = low, SHDN = high 200 FA Shutdown mode, SHDN = low Voltage Drop at ANTBIAS from Sourcing 20mA at ANTBIAS 0.2 V V CC RF Short-Circuit Protection Current at ANTBIAS is shorted to ground 57 mA ANTBIAS Active Antenna Detection Current To assert logic-high at ANTFLAG 1.1 mA DIGITAL INPUT AND OUTPUT Digital Input Logic-High 1.5 V Measure at the SHDN pin Digital Input Logic-Low 0.4 V Measure at the SHDN pin Idle Mode is a trademark of Maxim Integrated Products, Inc. Maxim Integrated 2 *The parametric values (min, typ, max limits) shown in the Electrical Characteristics table supersede values quoted elsewhere in this data sheet.