MAX4551/MAX4552/MAX4553 19-1391 Rev 0 10/98 15kV ESD-Protected, Quad, Low-Voltage, SPST Analog Switches General Description Features The MAX4551/MAX4552/MAX4553 are quad, low-volt- 15kV ESD Protection per IEC 1000-4-2 age, single-pole/single-throw (SPST) analog switches. +2V to +12V Single Supply Each switch is protected against 15kV electrostatic 2V to 6V Dual Supplies discharge (ESD) shocks, without latchup or damage. On-resistance (100 max) is matched between switch- 120 Signal Paths with 5V Supplies es to 4 max, and is flat (8 max) over the specified Low Power Consumption: <1W signal range. Each switch can handle Rail-to-Rail ana- log signals. The off-leakage current is only 1nA at 4 Separately Controlled SPST Switches +25C and 10nA at +85C. Rail-to-Rail Signal Handling The MAX4551 has four normally closed (NC) switches, and the MAX4552 has four normally open (NO) switch- Pin-Compatible with Industry-Standard es. The MAX4553 has two NC and two NO switches. DG211/DG212/DG213 These CMOS switches can operate with dual power TTL/CMOS-Compatible Inputs with Dual 5V or supplies ranging from 2V to 6V or a single supply Single +5V Supply between +2V and +12V. They are fully specified for sin- gle +2.7V operation. Ordering Information All digital inputs have +0.8V and +2.4V logic thresh- olds, ensuring TTL/CMOS-logic compatibility when PART TEMP. RANGE PIN-PACKAGE using 5V or a single +5V supply. MAX4551CEE 0C to +70C 16 QSOP Applications MAX4551CSE 0C to +70C 16 Narrow SO MAX4551CPE 0C to +70C 16 Plastic DIP Battery-Operated Equipment MAX4551C/D 0C to +70C Dice* Data Acquisition MAX4551EEE -40C to +85C 16 QSOP Test Equipment MAX4551ESE -40C to +85C 16 Narrow SO Avionics MAX4551EPE -40C to +85C 16 Plastic DIP Audio Signal Routing Ordering Information continued at end of data sheet. *Contact factory for dice specifications. Networking Pin Configurations/Functional Diagrams/Truth Tables TOP VIEW IN1 1 1 1 16 IN2 IN1 16 IN2 IN1 16 IN2 COM1 2 15 COM2 2 15 2 15 COM1 COM2 COM1 COM2 NC1 3 14 NC2 NO1 3 14 NO2 NO1 3 14 NC2 V- 4 V- V- 13 V+ 4 13 V+ 4 13 V+ MAX4552 MAX4553 GND 5 MAX4551 12 N.C. 5 5 12 GND 12 N.C. GND N.C. NC4 6 11 NC3 6 11 6 11 NO4 NO3 NO4 NC3 COM4 7 10 COM3 COM4 7 10 COM3 COM4 7 10 COM3 IN4 8 9 IN3 8 9 IN3 8 9 IN3 IN4 IN4 QSOP/SO/DIP QSOP/SO/DIP QSOP/SO/DIP MAX4551 MAX4552 MAX4553 SWITCHES SWITCHES LOGIC SWITCH LOGIC SWITCH LOGIC 1, 4 2, 3 ON OFF 0 0 0 OFF ON OFF ON 1 1 1 ON OFF N.C. = NOT CONNECTED SWITCHES SHOWN FOR LOGIC0 INPUT Rail-to-Rail is a registered trademark of Nippon Motorola, Ltd. Maxim Integrated Products 1 For free samples & the latest literature: 15kV ESD-Protected, Quad, Low-Voltage, SPST Analog Switches ABSOLUTE MAXIMUM RATINGS Voltages Referenced to GND Continuous Power Dissipation (T = +70C) A V+.....................................................................-0.3V to +13.0V QSOP (derate 9.52mW/C above +70C)....................762mW V- .....................................................................-13.0V to +0.3V Narrow SO (derate 8.70mW/C above +70C) ............696mW V+ to V- ............................................................-0.3V to +13.0V Plastic DIP (derate 10.53mW/C above +70C) ..........842mW All Other Pins (Note 1) ..........................(V- - 0.3V) to (V+ + 0.3V) Operating Temperature Ranges Continuous Current into Any Terminal..............................10mA MAX455 C E ......................................................0C to +70C Peak Current into Any Terminal MAX455 E E ...................................................-40C to +85C (pulsed at 1ms,10% duty cycle)...................................20mA Storage Temperature Range .............................-65C to +160C ESD per Method 3015.7 (IN , COM , V+, V-, GND) .......>2500V Lead Temperature (soldering, 10sec) .............................+300C IEC 1000-4-2 (NO , NC ) ..................................................15kV Note 1: Signals on NC , NO , COM , or IN exceeding V+ or V- are clamped by internal diodes. Limit forward-diode current to maximum current rating. Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICSDual Supplies (V+ = +5V, 10%, V- = -5V, 10%, T = T to T , unless otherwise noted. Typical values are at T = +25C.) A MIN MAX A MIN TYP MAX PARAMETER SYMBOL CONDITIONS T UNITS A (Note 2) ANALOG SWITCH Analog Signal Range V , V , COM NO C, E V- V+ V (Note 3) V NC +25C 80 120 COM to NO , COM to NC V+ = 5V, V- = -5V, V NO R ON On-Resistance or V = 3V, I = 1mA NC COM C, E 140 +25C 14 COM to NO , COM to NC V+ = 5V, V- = -5V, V NO On-Resistance Match Between R ON or V = 3V, I = 1mA NC COM C, E 5 Channels (Note 4) +25C 48 COM to NO , COM to NC V+ = 5V, V- = -5V, V NO On-Resistance Flatness R FLAT(ON) or V = +3V, 0, -3V NC C, E 10 (Note 5) +25C -1 0.01 1 NO , NC Off-Leakage Current I , V+ = 5.5V, V- = -5.5V, NO (OFF) nA (Note 6) I V = 4.5V, V = 4.5V NC (OFF) COM NO C, E -10 10 +25C -1 0.01 1 COM Off-Leakage Current V+ = 5.5V, V- = -5.5V, I nA COM (OFF) (Note 6) V = 4.5V, V = 4.5V COM NO C, E -10 10 +25C -2 0.01 2 COM On-Leakage Current V+ = 5.5V, V- = -5.5V, I nA COM (ON) (Note 6) V = 4.5V COM C, E -20 20 2 MAX4551/MAX4552/MAX4553