MAX79356 ZENO Flexible Narrowband OFDM Powerline Communication Modem with Integrated Analog Front End General Description Benefits and Features ZENO (MAX79356) is a programmable narrowband Supports All Standards and Frequency Bands to orthogonal frequency division multiplexing (OFDM)-based Reduce R&D Investment and Time to Market powerline communication (PLC) modem system-on-chip G3-PLC Certified (SoC) device that provides standards compliant high Compliant with, G3-PLC, IEEE 1901.2, ITU G9903, performance and secured powerline communication in PRIME a small package. ZENO integrates two pipelined 32-bit Supports Regulated Frequency Bands for RISC (MAXQ30E) processors to offer high performance Communication: CENELEC, FCC, ARIB and future-proof flexibility. These two 32-bit RISC proces- Accommodates Evolving Standards with Flexible sors perform dedicated PHY signal processing functions System Architecture That Integrates Dual 32-Bit and MAC layer functionality. Maxim provided, certified RISC Processors with 512KB Flash and 288KB RAM firmware images allow faster time to market. Factory or in- for MAC and PHY field firmware update feature allows adoption of changes Universal Firmware Supports Both PAN Coordinator and updates in PLC communication standards. The inte- and PAN Device Functionality grated high-speed AES-CCM* engine ensures standards Programmable Frequency Notching compliant data communication security and integrity. Efficient BOM for Building Competitive Modems Applications Supports All G3-PLC Bands with One SKU Smart Grid Communications Integrates MAC, OFDM PHY, and Analog Front Smart Meters End for Simplified Board Design Advanced Metering Infrastructure (AMI) Single 16MHz Crystal Generates All Operating Clocks AMI Concentrators UART Provides Simple Interface for Host Processor Factory and Building Automation Communications Electric Vehicle Charging Low Power Consumption (typ) Home Energy Monitoring 55mW in Listen Mode Solar and Renewable Energy Management 70mW in Active Mode Street Lighting Automation and Lighting Control High-Sensitivity Receiver with Adaptive Gain Control Allows Communication with Low Signal-to-Noise Ratio Ordering Information appears at end of data sheet. Integrated 128/256-bit AES and AES-CCM* Engine for Encryption/Decryption and Authentication Typical Operating Circuit MAXQ is a registered trademark and ZENO is a trademark of Maxim Integrated Products, Inc. 19-7548 Rev 2 9/17MAX79356 ZENO Flexible Narrowband OFDM Powerline Communication Modem with Integrated Analog Front End Absolute Maximum Ratings (All voltages referenced to AGND 0, AGND 1.) Digital Output Pins Supplies and Ground Pins TXD0, RTS0, READY, TXEN, LD MODE, G0, DVDD33 0, DVDD33 1, AVDD33 .......................-0.5V to +3.6V G1, MOSI, MOSI, SSEL, SCLK, COLLISION, DVDD12, AVDD12 ................................................-0.5V to +1.7V ACTIVITY .........................................-0.5V to V + 0.5V DVDD33 DGND 0, DGND 1, DGND 2..............................-0.2V to +0.2V Digital Input Pins Analog Output Pins RXD0, PROG/CTS0 , ZC1, ZC2, STATUS0, DVDD12 REG......................................................-0.5V to +1.7V STATUS1, MISO, RSTN ..................-0.5V to V + 0.5V DVDD33 TX N, TX P ........................................-0.5V to V + 0.5V Temperature AVDD33 Analog Input Pins Operating Junction Temperature (peak, 100ms) .............+140C RX N, RX P........................................-0.5V to V + 0.5V Operating Junction Temperature (continuous) ................+125C AVDD33 Oscillator Pins Storage Temperature Range ............................ -65C to +150C Lead Temperature (soldering, 10s) .................................+300C XIN, XOUT...........................................-0.5V to V + 0.5V DVDD33 Soldering Temperature (reflow) .......................................+260C Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Package Thermal Characteristics (Note 1) Junction-to-Ambient Thermal Resistance ( ) ..............46C/W Junction-to-Case Thermal Resistance ( ) ...................10C/W JA JC Note 1: Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a four-layer board. For detailed information on package thermal considerations, refer to www.maximintegrated.com/thermal-tutorial. Electrical Characteristics (Limits are production tested at T = +25C. Limits over the operating temperature range and relevant supply voltage range are A guaranteed by design and characterization.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS OPERATING CONDITIONS V , V = V = V DVDD33 0 AVDD33 DVDD33 0 DVDD33 1 Digital Supply Voltage 2.7 3.3 3.6 V V (Note 2) DVDD33 1 V = V = V AVDD33 DVDD33 0 DVDD33 1 Analog Supply Voltage V 3.0 3.3 3.6 V AVDD33 (Note 2) Operating Temperature -40 +85 C INTERNAL LOW DROPOUT (LDO) VOLTAGE REGULATOR V V = V = V , DVDD12 DVDD12 REG DVDD12 AVDD12 LDO Output Voltage 1.18 1.20 1.22 V internal LDO enabled (Note 3) REG SUPPLY MONITORS V Fail Warning Voltage DD33 V 2.85 3.05 V DD33PFW (Note 4) V Reset Voltage DD33 V 2.8 3.0 V DD33RST (Note 4) V Fail Warning Voltage DD12 V 1.157 1.19 V DD12PFW (Note 5) V Reset Voltage DD12 V 1.127 1.16 V DD12RST (Note 5) Maxim Integrated 2 www.maximintegrated.com