H5KLR-11 100-240V AC/DC Anly

ANLY COUNTER H5KLR MULTI-FUNCTION DIGITAL COUNTER CHARACTERISTICS : SPECIFICATION : Proximity and photoelectric switch Operating voltage AC/DC(V): 12~48 or 100~240 compatible Allowable operating 85~110% of rated operating voltage voltage range Protection against power surge and high Rated frequency 50 / 60 Hz frequency interference High-speed response allows 5,000 counts Contact rating 250VAC 5A (resistive load) per second Count speed MAX 30, 1K or 5K cps Online change of set value possible Reset time MAX 0.1s Four levels of key protection provided Power consumption Approx. 2.5VA Count Up, Count Down or Count Up/Down Mechanical: 5,000,000 times Life mode user selectable Electrical: 100,000 times Memory function available Ambient temperature -10 ~ +50 UL, C-UL recognized and CE certified Ambient humidity MAX 85%RH Weight Approx. 120g TYPE SELECTION : Type H5KLR-8 H5KLR-8B H5KLR-8M H5KLR-11 H5KLR-11M Count speed Max 30, 1K or 5K cps(user program selectable) Output contact 1C 1a 1a 2C 1C Memory External Reset Count Up Count Down Count Up/Down Product is subject to change without notice. B04Input 1 CONNECTION : H5KLR-8 H5KLR-8B H5KLR-8M H5KLR-11 H5KLR-11M (-) (+) DC 50mA Input 1 Input 2 Load RESET CP1 (Sensor) Input 1 RESET PNP Input 2 CP2 Input 1 Input 1 CP1 4 5 4 5 CP1 4 5 6 6 5 7 5 7 3 6 3 6 3 6 4 8 K / P 4 8 3 9 3 9 NPN 2 7 2 7 2 7 (-) CP2 / 2 10 2 10 1 11 1 11 18 18 RESET 18 Load (Sensor) NPN (+) Common Common PNP DC 50mA SOURCE SOURCE SOURCE SOURCE SOURCE NL NL NL NL NL K / P : Key Protection Note: NPN type => Common = 0V, PNP type => Common = +V. (whether can choose NPN type from PNP type by setting up parameter) TIMING CHART : Input Modes and Count Value Please note: 1. indicates minimum signal width indicates 1/2 of minimum signal width. Signals may not be counted if the minimums for A and B are not met. 2. H and L Signal No-voltage input Voltage input H Short circuit 4.5 ~ 30 VDC L Open circuit 0 ~ 2 VDC Up (increment) mode - Count at rising edge Down (decrement) mode - Count at rising edge H H CP1 CP1 L L A A A A Inhibit Inhibit H H CP2 CP2 L L n 5 n-1 4 n-2 Count Count 3 n-3 2 n-4 1 n-5 0 0 0 Up (increment) mode - Count at falling edge Down (decrement) mode - Count at falling edge H H CP1 CP1 L L A A A A Inhibit Inhibit H H CP2 CP2 L L n 5 n-1 4 n-2 Count Count 3 n-3 2 n-4 1 n-5 0 0 0 Up/Down A Command input mode Up/Down B Individual input mode H H CP1 CP1 L L A A H H CP2 CP2 L L 3 3 3 3 Count Count 2 2 2 2 2 2 1 1 1 1 1 0 0 0 0 Up/Down C Phase difference input mode (See note 1.) H CP1 L BBB B H CP2 L 3 3 Count 2 2 2 1 1 0 Note 1. Set the same counting speed for CP1 and CP2 when in Up/Down C mode. 0 CP1 RESET OUT2 CP2 CP1 RESET OUT2 Common Input 2 OUT2 OUT1 Common OUT2 Common OUT2