03-Serie IM-A 08-Serie IP-A 31/10/14 08:02 Page11 IM series Sealed snap-action pushbutton switches - bushing 12 mm - momentary Distinctive features and specifications UG1410A Snap-action : tactile feedback with audible click High current/voltage rating Sealed to IP67 Flat round actuator for optional marking B1 ENVIRONMENTAL SPECIFICATIONS MATERIALS Front panel sealing : IP67 according to IEC 60529 Case : polyamide 4/6 Shock resistance : 50 g - 11 ms according to IEC 68-2-27 Actuator : polyamide 6/6 Salt spray : IEC 512-6, test 11f Bushing/bezel : polyamide 6/6 Operating temperature : -40C to +85C Contacts : silver, gold plated Storage temperature : -40C to +85C Terminal seal : epoxy ELECTRICAL SPECIFICATIONS AGENCY APPROVAL Max. current/voltage rating with resistive load : 3A 28VDC 2A 125VAC/250VAC Initial contact resistance : 100 m max. File E83438 Insulation resistance : 1 G min. at 500VDC Availability : consult factory for Dielectric strength : 500 Vrms between terminals details of approved models. Electrical life at full load : 25.000 cycles Marking : to order switches marked UL, complete approrpiate box of GENERAL SPECIFICATIONS ordering format. Panel thickness : 1,5 mm (.059) to 10 mm (.394) Total travel : 1,7 mm (.067) +/- 0,3 mm Low level or mechanical life : 1.000.000 cycles Torque : 1,5 Nm max. applied to nut MOUNTING - STANDARD BEZEL Panel cut-out Matrix mounting Back of panel space requirement 20.00 20.00 (.787) (.787) 12.90 (.507) 1 13.60 (.535DIA) 13.50 (.531DIA) Flat seal MOUNTING - REDUCED BEZEL Panel cut-out Matrix mounting Back of panel space requirement 17.50 17.50 (.689) (.689) 12.90 (.507) 2 13.60 (.535DIA) 13.50 15.60 (.531DIA) (.614DIA) O-ring APEM www.apem.com B1-11 0.80min-4.30Max 1.50min-10.00Max (.031MIN.-.169MAX.) (.059MIN.-.393MAX.) 1.50min-10.00Max (.059MIN.-.393MAX.) 17.50 20.00 (.689) (.787) 20 20 (.787) (.787)03-Serie IM-A 08-Serie IP-A 31/10/14 08:02 Page12 IM series Sealed snap-action pushbutton switches - bushing 12 mm - momentary Overview IM SERIES Actuator shape Electrical function Terminals Contacts R Round, curved 7 NC + NO P Straight PC 4 Silver, gold Z Quick-connect plated (standard) P Round, flat B1 Actuator colours Bushing & bezel Bezel options Actuator option Approval finish 1 Blue Blank Standard bezel Blank Std actuator UL 2 Black B Dark blue 075 Dia. 15 (.590) reduced 104 High actuator Consult factory for 2 Black bezel, frontal mounting detail of approved Other : on request 3 Green 234 Dia. 15 (.590) reduced models. 4 Grey bezel, std mounting 5 Yellow 6 Red 7 White 9 Orange ABOUT THIS SERIES On the following pages, you will find successively : model structure of switches and options in the same order as in above chart Dimensions : first dimensions are in mm while inches are shown as bracketed numbers. NOTICE : please note that not all combinations of above numbers are available. Refer to the following pages for further information. A sealing boot is available to protect the switches against frost and sand (P/N U5125). It is presented after the IA series and in section H. Mounting accessories : Standard hardware supplied : 1 flat seal (standard bezel) or 1 O-ring (reduced bezel) and 1 hex nut 14 mm (.551) acrosss flats. Hex nut part number U166. Packaging unit : 50 pieces The company reserves the right to change specifications without notice. B1-12 www.apem.com APEM