04-Serie IP-A-R1-FilsFins 08-Serie IP-A 31/10/14 08:04 Page15 IP series Pushbutton switches for harsh environments - bushing 12 mm - momentary Distinctive features and specifications UG1410A Illuminated or non-illuminated Tactile feedback Wide variety of configurations Flat round actuator for optional marking Sealed to IP67 B1 ENVIRONMENTAL SPECIFICATIONS GENERAL SPECIFICATIONS Front panel sealing : IP67 according to IEC 60529 Panel thickness : 1,5 mm (.059) min. IP69K according to DIN 40050-9 (non-illuminated) with cap U5125 4 mm (.157 max.) Shock resistance : 100 g according to IEC 512-4, test 6c Total travel : Vibration resistance : 10-500Hz - 10 g according to IEC 512-4, test 6d Funct. 3 : 1,7 mm (.067) +/- 0,3 mm Salt spray : IEC 512-6, test 11f Funct. 5 : 1,3 mm (.051) +/- 0,3 mm Robustness (non-illuminated) : IK06 according to EN 50102 (1 joule) Typical operating force : 6N +/- 2N Operating temperature : -40C to +85C Low level/mech. life : 1.000.000 cycles Torque : 1,5 Nm max. applied to nut Soldering : 320C max. for 3 sec. ELECTRICAL SPECIFICATIONS Max. current/voltage rating with resistive load (gold plated silver contacts): MATERIALS 5A 28VDC, 70.000 cycles For W terminals, current has to Case : thermoplastic UL94-V0 0,2A 48VDC, 500.000 cycles be limited to 400mA. Actuator : polyamide 6/6 0,5A 48VAC, 500.000 cycles Bushing/bezel : zinc die-cast Initial contact resistance : 100 m max. (zamac), black painted Insulation resistance : 1 G min. at 500VDC Contacts : silver, gold plated (std) Dielectric strength : 1.500 Vrms brass, gold plated (for option 104) Contact bounce : 10 ms Output wires (flying lead terminals) : LED COMPONENT SPECIFICATIONS 2 F version : AWG20, section 0,6 mm 2 W version : AWG24, section 0,23 mm LED colour Forward current Typ. forward voltage Max. forward voltage LED wires : Super red (L0S) 20mA 2,1V 2,3V 2 F version : AWG26, section 0,12 mm Yellow (L0Y) 20mA 2,1V 2,3V 2 W version : AWG24, section 0,23 mm Lens : polycarbonate Green (L0G) 20mA 2,1V 2,3V Terminal seal : epoxy Blue (L0B) 20mA 3,2V 3,8V White (L0W) 20mA 3,35V 4,25V AGENCY APPROVAL A resistor must be series-connected by the user. 2A 125VAC/250VAC supply voltage - LED forward voltage Resistor value = File E83438 LED forward current See following pages. MOUNTING Panel cut-out Matrix mounting Back of panel space requirement 20.00 20.00 12.90 (.507) (.787) (.787) 1 13.60 (.535DIA) 13.50 (.531DIA) O-ring APEM www.apem.com B1-15 1.50min-4Max (.059 min-.157max) 20.00 (.787) 17.50 (.688)04-Serie IP-A-R1-FilsFins 08-Serie IP-A 31/10/14 08:04 Page16 IP series Pushbutton switches for harsh environments - bushing 12 mm - momentary Overview IP SERIES Actuator shapes Electrical functions Terminals Contacts C Square 3 Normally open S Solder lugs AD Silver, gold (NO) F Flying leads, standard plated (standard) R Round, curved 5 NC/NO combined W Flying leads, thin NEW CD Brass, gold P Round, flat (non-illuminated) P Straight PC plated (option 104) Z1 Quick-connect (non-ill., NO only ) B1 Actuator colours LED colours Options Approval 1 Blue Blank Non-illum. 100 Satin chrome UL B Dark blue L0S Super red bezel Consult factory for 2 Black L0Y Yellow 101 Bright chrome detail of approved 3 Green L0G Green bezel models. 4 Grey L0B Blue 104 High actuator 5 Yellow L0W White (non-illum. round 6 Red models only) 7/1 White 8 Bright chrome Option 104 9 Orange If combined with electrical function 5 (NC/NO), this A Satin chrome option should be ordered with CD contacts (brass, gold plated). Current/voltage rating : 100mA 30VDC ABOUT THIS SERIES On the following pages, you will find successively : model structure of switches and options in the same order as in above chart Dimensions : first dimensions are in mm while inches are shown as bracketed numbers. NOTICE : please note that not all combinations of above numbers are available. Refer to the following pages for further information. A sealing boot is available to protect the switches against frost and sand. It is presented after the IA series and in section H. Mounting accessories : Standard hardware supplied : 1 hex nut 14 mm (.551) across flats and 1 O-ring. Hex nut part number U166. Packaging unit : 25 pieces The company reserves the right to change specifications without notice. B1-16 www.apem.com APEM