LPI series Tactile pushbutton switches with large actuator Distinctive features and applications Common features Large ergonomic actuator ( 35 mm) Tactile feedback Low behind-panel depth (21 mm max.) Stylish design Long life B2 This series has been developed on a modular base in order to fit the exact needs of technicians and end-users. Installation options The LPI series has a number of features to ensure easy installation: Front or rear mounting With or without sealing 2 separate circuits for NO/NC 5A version Terminal block connector for 0,1A NO version 3 different LED voltages: 6V, 12V, 24V Integrated LED resistor Aesthetic options Ring or dot illumination Wide range of LED colours Wide range of bezel colours Many different actuator types and colours Designed to meet the requirements of EN81-70 This product meets the requirements of EN81-70 and is ideal for use in all types of indoor lifts. Flexibility of marking The company reserves the right to change specifications without notice. APEM www.apem.com B2-161LPI series Tactile pushbutton switches with large actuator Specifications ELECTRICAL SPECIFICATIONS MATERIALS Snap-action, momentary function Switch block : thermoplastic for Mechanical life : 1.000.000 cycles min. for 5A NO/NC 5A NO/NC 5.000.000 cycles min. for 50mA NO Contacts : Max. currrent/voltage rating with resistive load : 5A NO/NC : silver, gold plated 50mA NO : silver 5A NO/NC version 50mA NO version Actuator crimped symbol : 304L stainless steel 5A 12VDC - 50.000 cycles 50mA 24 VDC - 5.000.000 cycles 100mA 12VDC - 1.000.000 cycles MECHANICAL SPECIFICATIONS Min. current with resistive load : 0,5mA at 24VDC for NO version Environmental protection : Contact resistance : 100m max. - IP53 for sealed version B2 Dielectric strength : 500Vrms 50Hz between terminals - IP40 for unsealed version 1.000 Vrms 50 Hz between terminals and ground Impact resistance : Insulation resistance : 10M at 500VDC - IK06 for NO/NC version Integrated resistors for illuminated versions - IK04 for NO version LED current : 20mA typical for dot or ring (30mA max.) Operating force : 2,5 to 5N (unsealed) LED protected from reverse polarity Total travel : 2 mm 0,3 mm Stand-by consumption : 0,5VA max. Operating temperature : - 20C to +65C Storage temperature : - 40C to +70C PANEL CUT-OUT 1 to 4 mm 1 to 4 mm 40.00 40.00 Panel thickness : 1 to 4 mm (.039 to .157) (.039 to.157) (.039 to.157) ((11..557744)) M4 M4 11 ttoo 44 mmmm ((..003399 ttoo..115577)) Unsealed version ++00..2200 39.10 39.10 -0.00 -0.00 (1.539DIA 0/+0.001) (1.539DIA 0/+0.001) Rear mounting 1 to 4 mm 1 to 4 mm 40.00 (.039 to.157) 40.00 (.039 to.157) (1.574) (1.574) 4.00 4.00 +0.20 +0.20 38.10 -0.00 38.10 -0.00 (.157 DIA) (.157 DIA) (1.5DIA 0/+.001) (1.5DIA 0/+.001) Front mouting Sealed version +0.20 +0.20 44.10 2.50 44..0000 44.10 --00..0000 2.50 ((11..773366DDIIAA 00//++00..000011)) (.098) ((..115577 DDIIAA)) (.098) B2-162 www.apem.com APEM +0.20 +0.20 3366..5500 --00.0.000 ((11..443377 00//++00..000011)) 40.00 40.00 40.00 40.00 ((11..557744)) ((11..557744))