Specifications 231A models 230A 231A 235 Cable Type 10BaseT 10Base2 100BaseTx RJ45 RJ11 356A TIA-568A TIA-568B Token Ring Test Type Open Short Reverse Cross Split Power Source 9V Battery 9V Battery 9V Battery Dimensions (HxWxD) 5.4x3x1.6 5.2x3x1.6 4.1 x 3 x 1.4 230A (137 x 76 x 40mm) (132 x 76 x 40mm) (103 x 75 x 36mm) Weight 6.8oz. (193g) 7.1oz. (201g) 0.4 lbs. (185g) One Year Warranty Accessories SUPPLIED: Master Unit Master Unit Master Unit Remote Terminator Remote Terminator Remote Terminator 3 Patch Cables Carrying Case BNC to BNC adapter Model 231A Deluxe Multi-Network Cable Tester Model 230A The 231A can easily read the correct pin configuration of 10BaseT cable (cate- gory 5), 100BaseTx, 10Base2 cable (coax) and RJ45/RJ11 modular cables, Multi-Network Cable Tester 356A, TIA-568A, TIA-568B and Token Ring cables by comparing one trans- The 230A tests thin Ethernet (BNC), 10BaseT (UTP/STP), 100BaseTx, RJ45, TIA- mitting end to the corresponding receiving end. With the remote kit, it can test 568A, TIA-568B, and Token Ring cables within a few seconds. It detects miswiring, cables installed far away either on wall plate or patch panel up to 1000ft away. polarization, and continuity. The 230A also tests the ground of shielded twisted It is easy to verify the cable continuity, open, short, and cross connect, featur- pair cables. With the remote unit, you can remotely test installed cable either from ing auto or manual scan for pin-out indicators. the wall plate or patch panel. Tests 10BaseT, 100BaseTx, 10Base2, RJ45, RJ11, 356A, Auto scans thin Ethernet (BNC),10Base T (UTP/STP), TIA-568A,TIA-568B, and Token Ring cables 100BaseTx, RJ45, 356A,TIA-568A,TIA-568B, and Token Ring Detects open, short, cross, and continuity cables in seconds Tests Point-to-Point, rather than Pair-to-Pair Detects miswiring, polarization, and continuity Quick and easy to use Also tests the ground of shielded twisted pair cables Tests cables on wall plate or patch panel up to 1000 ft away Tests cables before or after installation with the remote unit with the remote kit LED display for clear indication of problems Easy to read LED display Protective rubber boot Protective rubber boot Belt clip Belt clip 78235 Model 235 Remote Network Cable Tester The 235 network cable tester is an easy and effective cable tester which can test all the wiring faults of 10Base2 (Coax), 10BaseTx, 100Base Tx, RJ45, 356A, TIA-568A, TIA-568B and Token Ring cables. It can identify not only the wiring faults, such as open pairs, shorted pairs, reversed pairs, crossed pairs and split pairs, but can also identify up to 4 different cables at one end. 240 A large flashing LED displays the fault code, and the 4 pairs individual LEDs tells you which pairs are tested. The remote identifiers are provided to make a remote test. Just push the TEST switch. It will automatically run all tests Model 240 within a few seconds and show you what faults are present. It is simple and Remote Network Cable Analyzer easy to use. The 240 is a small handheld tester which enables the user to quickly read the status of Ethernet twisted pair cables. The 240s tone generator feature can be used to Detects open, short, reversed, crossed, and split trace installed cables and locate areas of discontinuity. Clear LED display for the fault status Simple and easy to use The 240 includes one master unit and one remote and can be operated easily by one Test cable length:Minimum - 4ft (1.2m) Maximum - person testing patch cords or installed cables. 492ft (150m) Testing of twisted pair cables Special designed remote unit Identify up to 4 different cables at one end by provided for open circuits, shorts, that enables one-person testing remote identifiers crossed pairs, reversed pairs of installed cables Tests: 10BaseT, 100BaseTx, 10Base2 (coax), RJ45, 356A, and split pairs Small remote unit that slides TIA-568A,TIA-568B and Token Ring, etc. Minimum length for split into master unit for convenient pair detection is 1.97ft (0.6m) and safe storage Testing of twisted pair cables Automatic sleep mode and over 450ft (135m) in length power switch to decrease Tone generator for tracing power consumption Model 240P installed cables and locating Low battery LED Cable Tracer Probe faults (use with 240P) Dimensions (HxWxD): 4.93 x Used in conjunction with the tone generator function on Shield integrity testing 2.05 x 1.18 (125 x 52 x 30mm) the 240 Remote Network Cable Tester or any tone Cross talk detection in excess Weight: 0.28lbs. (130g) generator in the market, the 240P Cable Tracer of 3dB +0.3dB at 3.5MHz Accessories Supplied: Master can trace cables and locate faults, even when cables are in a bundle or hidden in a mess of between any two pairs unit, Remote terminator, one punch down blocks or wall plates. patch cable, carrying case. One Year Warranty Special inductive plastic tip which prevents accidental shorts (possible with copper-tip tracers) when using near high voltage devices Traces and identifies wires or cable in a bundle or group without damaging cable insulation Adjustable volume tone amplifier and an LED indicator Power Supply: 9V battery (not included) Dimensions (HxWxD): 8.07 x 1.42 x 1.42 (205 x 36 x 36mm) 240P Weight: 0.26lbs. (110g) Accessories included: Manual One Year Warranty 79 For your nearest distributor, call 800-462-9832 or www.bkprecision.com