Accessories
Front Panels and DIN-Racks
Front Panels
Description
Front panels are available for 19" DIN-rack mounting of 3 U
cassette type power supplies in Schroff system version
(Intermas system on request) and may be attached to the
converter by means of countersunk screws.
An assembly kit, consisting of a front panel and a support
bracket, enables arrangement of two standard cassettes with
up to six output voltages in 6 U configuration.
All front panels are of colorless anodized aluminum and
delivered with one or 2 grey plastic handles of 3 TE for easy
pull-out and 2 or 4 hand-press insertable plastic retainers with
captive screws for fixing to the rack.
Note: Custom specific front panels are available on request.
Dimensions according to DIN 41494-1 (IEC 60297):
Width: 1 TE =5.08 mm (0.2")
Height: 1 U = 44.45 mm (1.75)
Tolerances: 0.2 mm, unless otherwise specified.
Note: In Europe, often HE instead of U is used.
Schroff System for 3 U Rack
Q-, P- Series Front Panels in 4, 5, or 6 TE
0.1 0.1
6.4 2.5
These front panels available in three versions and fit to all
DC-DC converters of the Q, P and HP Series; see fig. 1 for the
mechanical details.
Table 1: Front panel selection for P and Q Series
T E X Case Conv. Panel Designation
mm series type
413
4 20.0 Q01, Q05 Q, HP G04-Q01 HZZ00835
Q04 P G04-Q04 HZZ00840
5 25.1 Q01, Q05 Q, HP G05-Q01 HZZ00836
Q04 P G05-Q04 HZZ00841
6 30.2 Q01, Q05 Q, HP G06-Q01 HZZ00839
Q04 P G06-Q04 HZZ00842
8 40.3 Q01, Q05 Q, HP G08-Q01 HZZ00846
Q04 P G08-Q04 HZZ00850
X
Note: For using several units nearby to each other, we advise to
pack them not too densely, in order to assure good thermal
management (see also relevant data sheet).
Cut out for P Series only
Delivery contents:
Front panel, grey plastic handle, 3 countersunk screws, set of
Fig. 1
2 plastic retainers with captive screws, and assembly
Front panel for Q, P and HP Series converters
instruction.
MELCHER
The Power Partners.
BCD.00495 Rev AC, 02-Jun-2016 Page 1 of 5
128.4
122.4
0.2
13 20.6 50 9.5
0.1 0.1
9.2 104
12002aAccessories
Front Panels and DIN-Racks
Front Panels 8 TE for M and LH Series
0.1
0.1
18.4
2.5
This front panel fits to all 50 Watt DC-DC and AC-DC
converters of the M Series (case M02) and LH Series (case
H02).
Table 2: Front panel selection for M and LH Series
12.2
T E mm Case Converter Panel type
size series Designation
26
8 40.3 M02 M G08-M02
HZZ00802
H02 LH
Delivery content:
Front panel with grey plastic handle, 2 countersunk screws,
set of 2 plastic retainers with captive screws, and assembly
instruction.
0.1 0.1
0.1
31.5 2.5
4.4
40.3 (8 TE)
cut out for option D
426
Fig. 3
Front panel for PSL Series
Front Panels 12 TE for S, HR, HRL, ER, ERL, PSS
Front Panels 16 TE for K, HRP, ERP, PSK
These front panels fit to the converter series mentioned in the
table below
Table 4: Front panel selection for S, K, PSS, PSK, and all R
Series converters
Width x Case Converter Panel type
40.3 (8 TE)
T E mm size series Designation
12 60.6 S01 PSS G12-S
Fig. 2
HZZ00845
Front panel for M and LH Series
S02 S
S03 ERL, HRL
Front Panels 8 TE for PSL Series
16 81.0 K01 PSK G16-K
HZZ00831
This front panel fits to the Switching Regulators of the PSL
K02 K
Series (case size L04).
K03 ERP, HRP
Table 3: Front panel selection for PSL Series
Delivery contents:
T E mm Case Converter Panel type
Front panel with grey plastic handle, two countersunk screws,
size series Designation
set of four plastic retainers with captive screws and assembly
8 40.3 L04 PSL G08-L instructions.
HZZ00805
PSL with opt. D G08-L04-D
HZZ00816
Delivery contents:
Front panel with grey plastic handle, 2 countersunk screws,
set of 2 plastic retainers with captive screws and assembly
instructions.
MELCHER
The Power Partners.
BCD.00495 Rev AC, 02-Jun-2016 Page 2 of 5
128.4
122.4
0.2
50 9
0.1 0.1
18.2 94.5
12003a
128.4
122.4
0.2
85
50.5 7
0.1 0.1
11.7 100
12004a