BH-ADP-ISOARM Blackhawk

Whats Included Isolation Adapter PC Board 20-pin Ribbon Cable (0.100 x0.100) 10-pin Ribbon Cable (0.050 x 0.050) Bump-ons (4) Quick Start Guide Warranty and Product Registration Information Blackhawk JTAG Isolation Adapter for ARM JTAG Isolation Protection for your Equipment (ISOARM) The Blackhawk JTAG Isolation Adapter for Features ARM is a board that connects between your JTAG emulator and the JTAG connection of Supports I/O voltages of 1.8V-5.0V targets your target board. The adapter is designed to Serial wire debug (SWD) and IEEE 1149.1 (JTAG) protocols supported minimize and protect connected devices (PC/ Emulator/Target) from ground loop voltage, High electromagnetic immunity harsh environments and new, untested High Speed operation: up to 24MHz TCK designs. Connections: ARM Std 20-pin, ARM Cortex 10 & 20-pin The adapter is very flexible by providing three JTAG connection options (Std. 20-pin ARM, 10 Voltage Isolation: 5K Vrms and 20-pin ARM Cortex) on both emulator Powered by USB, Target VCC or Emulator and target sides. This also allows the adapter Current consumption is 20-80mA (varies with I/O voltage level and SW3 setting) to be used as a converter from one JTAG connection type to another. RoHS Compliant The signal interface supports both standard JTAG (1149.1) and serial wire debug (SWD) JTAG Connector Signal Definitions SWD signals protocols, eliminating the need to purchase two different isolators. PIN 20-pin ARM 20-pin Cortex 10-pin Cortex PIN 20-pin ARM 20-pin Cortex 10-pin Cortex The emulator and target sides of the adapter 1 VCC VCC VCC 2 VCC TMS SWDIO TMS SWDIO are powered from the target side VCC signals, 3 nTRST GND GND 4 GND TCK SWDCLK TCK SWDCLK however, the emulator side can be powered 5 TDI NC GND GND 6 GND TDO SWO TDO SWO from USB or JTAG Emulator connectors with SW3 off to reduce power draw from the 7 TMS SWDIO KEY KEY 8 GND TDI NC TDI NC target should it be necessary. 9 TCK SWDCLK GND GND 10 GND nRESET nRESET These features in addition to the high 11 RTCK PWR 12 GND GND electromagnetic immunity, make this adapter 13 TDO SWO PWR 14 GND GND a very versatile solution to protect your 15 nRESET GND equipment. 16 GND GND 17 NC GND 18 GND GND Ordering Information 19 PWR GND 20 GND GND Part Number: BH-ADP-ISOARM J1 Pin 19: This pin is used as power input from the emulator (i.e. JLINK). SKU: 12216 J7 Pins 11 & 13: These pins are used as power input from the emulator (i.e I-JET). For more information, or to order this VCC J2, J4 & J6: The VCC signal pins on the target side supply power for isolator IC logic, LEDs and emulator side. product online, please visit our website at J1, J3 & J7: The VCC signal pins on the emulator side are fixed at 3.3V. www.blackhawk-dsp.com.com (SW3 can be used to turn off power to emulator side if necessary). Learn More: For more information about Blackhawk products, please visit www.blackhawk-dsp.com Blackhawk is a trademark of EWA Technologies, Inc. All other product or service names are the property of their respective owners. Copyright EWA Technologies, Inc. 2019. All rights reserved. EWA Technologies, Inc. reserves the right to make changes in design or specification at any time and without notice. ISOARM-DS-01 - 09/23/2019 X-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for Sockets & Adapters category: Click to view products by Blackhawk manufacturer: Other Similar products are found below : 6508-0-00-01-00-00-33-0 AC164348 1262 22827 AC164353 TDGL015 SA247 SM64TQ-ACTEL-1 70-0036 8.06.03 DS91230+ SMPA- ISP-ACTEL-3-KIT 16017 LFVDBGF KIT 70601-3 SM132CQ-ACTEL IPC0181 IPC0175 IPC0165 AC164397 conga-Thin MITX/eDP to DP Adapter SLG46621V-SKT SLG46722V-SKT ML-ADP-EVN ASA.01 ASA.09 ASA.12 ASA.14 TOOLSTICK990MPP C305000ACP2 110-83-320-41-605101 110-83-632-41-605101 110-83-640-41-605101 110-83-628-41-605101 116-83-306-41-001101 PA0003 PA0007 PA0009 PA0035 PA0085 PA0096 IPC0079 ATARD-DBGADPT 80-000286 ATSTK600-RC46 ATSTK600-RC88 ATSTK600-SC06 ATSTK600-RC78 SPC560PADPT64S AC164345