BH-20e_cTI-20t_ARM Blackhawk

Blackhawk QUICK 3 20e cTI-60t TI Pin Converter JTAG START Pin The 20e cTI-60t TI Pin Converter is designed to attach an emula- tor cable with a 20-pin cTI JTAG connection to a target board with 60 GUIDE Converters(20e cTI) pin trace connector. 1. Make sure the target is not powered when connecting Installation Requirements 2. Connect the 20 pin Male connector to your cTI emulator. 3. Connect the 60 pin Male socket to your target board. Emulator with new compact 20 pin TI (cTI) JTAG socket TI development Board with 14, 20(ARM), or 60 pin JTAG header WARNING Caution should be exercised in connecting this adapter to the JTAG emulator and the target JTAG header. Pay special attention to the Compact TI (cTI) 20-Pin Pin Converters JTAG Header Signal Table orientation and keying and pin outs. Be careful to connect with the correct orientation. This adapter is not intended to be hot pluggable. This document covers the installation Pin Name Pin Name Unplug power from all sources prior to connect or disconnect. and use of (3) pin converters de- signed to work with an emulator that 1 TMS 2 nTRST has the new compact TI (cTI) 20-pin 60-Pin Target TI Header Pin out JTAG connection (header pin to sig- 3 TDI 4 TDIS Pin Name Pin Name Pin Name nal shown in the table to the right). A1 GND B6 EMU12 C11 EMU6 The pin converters described in this 5 TVD 6 KEY A2 GND B7 TDO C12 EMU4 document are:. A3 GND B8 TVD C13 EMU3 7 TDO 8 GND 20e cTI-20t ARM Pin Converter A4 GND B9 EMU9 C14 EMU1 For connecting to a target board 9 RTCK 10 GND A5 GND B10 EMU7 C15 ID3 with 20-pin MultiICE connector. A6 GND B11 EMU5 D1 NC FIGURE 1Typical target board cable 11 TCK 12 GND A7 GND B12 TCLK D2 GND connection orientation 20e cTI-14t TI Pin Converter A8 TYPE 0 B13 EMU2 D3 GND For connecting to a target board 13 EMU0 14 EMU1 Target Board Connection: with standard TI 14-pin JTAG A9 GND B14 EMU0 D4 GND 60 pin SAMTEC connector (pin 6 keyed). 15 16 GND A10 GND B15 ID1 D5 GND nSRST connector A11 GND C1 ID2 D6 GND 20e cTI 60t TI Pin Converter 17 EMU2 18 EMU3 A12 GND C2 EMU18 D7 GND For connecting to a target board Emulator Connection: A13 GND C3 TRST/ D8 TYPE 1 that has the TI 60-pin trace 19 EMU4 20 GND 20 pin cTI male header header. A14 GND C4 EMU16 D9 GND (0.050 x 0.100) Signals are active low A15 TGTRST/ C5 EMU15 D10 GND B1 ID0 C6 EMU13 D11 GND B2 TMS C7 EMU11 D12 GND Important Environmental Considerations B3 EMU17 C8 TCLKRTN D13 GND Caution is necessary to minimize ESD (Electro-static Discharge) which can damage Blackhawk B4 TDI C9 EMU10 D14 GND 123 Gaither Drive electronic components. Use in a controlled environment where ESD materials and B5 EMU14 C10 EMU8 D15 GND Mt. Laurel, NJ 08054-1701 practices are employed is highly recommended. www.blackhawk-dsp.com +1-877-983-4514 4 Blackhawk is a registered trademark of EWA Technologies, Inc. BH-ADP-20e cTI-QS-02 1 1 20e cTI-20t ARM Pin Converter 20e cTI-14t TI Pin Converter 2 The 20e cTI-14t TI Pin Converter is designed to attach an emula- The 20e cTI-20t ARM Pin Converter is designed to attach an emula- tor cable with a 20-pin cTI JTAG connection to a target board with 14 tor cable with a 20-pin cTI JTAG connection to a target board with 20 pin connector with pin 6 keyed. pin MultiICE connector. 1. Make sure the target is not powered when connecting 1. Make sure the target is not powered when connecting 2. Connect the 20 pin Male connector to your cTI emulator. 2. Connect the 20 pin Male connector to your cTI emulator. 3. Connect the 14 pin Female socket to your target TI. 3. Connect the 20 pin Female socket to your target ARM. WARNING WARNING Caution should be exercised in connecting this adapter to the JTAG Caution should be exercised in connecting this adapter to the JTAG emulator and the target JTAG header. Pay special attention to the emulator and the target JTAG header. Pay special attention to the orientation and keying and pin outs. Be careful to connect with the orientation and keying and pin outs. Be careful to connect with the correct orientation. This adapter is not intended to be hot pluggable. correct orientation. This adapter is not intended to be hot pluggable. Unplug power from all sources prior to connect or disconnect. Unplug power from all sources prior to connect or disconnect. 20-Pin Target ARM Header Pin out TI 14-Pin Target Header Pin out Pin Name Pin Name Pin Name Pin Name 1 VDD 2 VDD 1 TMS 2 nTRST 3 4 GND nTRST 3 TDI 4 GND 5 TDI 6 GND 7 TMS 8 GND 5 TVD 6 KEY 9 TCK 10 GND 7 TDO 8 GND 11 RTCK 12 GND 9 RTCK 10 GND 13 TDO 14 GND FIGURE 1Typical target board cable FIGURE 1Typical target board cable connection orientation connection orientation 15 16 GND 11 TCLK 12 GND nSRST 17 NC 18 GND 13 EMU0 14 EMU1 19 NC 20 GND Signals are active low Signals are active low Target Board Connection: Emulator Connection: Target Board Connection: Emulator Connection: 14 pin female socket header - 20 pin cTI male header 20 pin cTI male header 20 pin female socket header pin 6 keyed. (0.100 x 0.100) (0.050 x 0.100) (0.050 x 0.100) (0.100 x 0.100) 2 3