6N139#300 Broadcom

HCPL-0700, HCPL-0701, HCNW138, HCNW139, 6N139, 6N138, Low Input Current, High Gain Optocouplers Data Sheet Lead (Pb) Free RoHS 6 fully compliant RoHS 6 fully compliant options available -xxxE denotes a lead-free product Description Features High current transfer ratio 2000% typical (4500 % These high gain series couplers use a Light Emitting typical for HCNW139/138) Diode and an integrated high gain photodetec tor to provide extremely high current transfer ratio between Low input current requirements 0.5 mA input and output. Separate pins for the photodiode TTL compatible output 0.1 V V typical OL and output stage result in TTL compatible saturation Performance guaranteed over temperature 0C voltages and high speed operation. Where desired the to 70C V and V terminals may be tied together to achieve CC O Base access allows gain bandwidth adjustment conventional phot odarlington operation. A base High output current 60 mA access terminal allows a gain bandwidth adjustment to Safetyapproval be made. - UL recognized 3750 V rms for 1 minute and 5000 V The 6N139, HCPL-0701, and HCNW139 are for use in rms* for 1 minute per UL 1577 CMOS, LSTTL or other low power appli ca tions. A 400% - CSA approved minimum current transfer ratio is guaranteed over 0 to 70C - IEC/EN/DIN EN 60747-5-5 approved with V = IORM operating range for only 0.5 mA of LED current. 1414 V for HCNW139 and HCNW138 peak The 6N138, HCPL-0700, and HCNW138 are designed for Available in 8-Pin DIP or SOIC-8 footprint or widebody use mainly in TTL applications. Current Transfer Ratio package (CTR) is 300% minimum over 0 to 70C for an LED current MIL-PRF-38534 hermetic version available of 1.6 mA (1 TTL Unit load ). A 300% minimum CTR (HCPL-5700/1) enables operation with 1 TTL Load using a 2.2 k Applications pull-up resistor. Ground isolate most logic families TTL/TTL, CMOS/ Functional Diagram TTL, CMOS/CMOS, LSTTL/TTL, CMOS/LSTTL Low input current line receiver NC 1 8 V CC High voltage insulation (HCNW139/138) EIA RS-232C line receiver TRUTH TABLE 7 ANODE 2 V B Telephone ring detector LED V O ON LOW 117 V ac line voltage status indicator low input 6 CATHODE 3 V OFF HIGH O power dissipation Low power systems ground isolation NC 4 5 GND * 5000 V rms/1 minute rating is for HCNW139/138 and Option 020 (6N139/138) products only. A 0.1 F bypass capacitor connected between pins 8 and 5 is recommended. CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD. The components featured in this datasheet are not to be used in military or aerospace applications or environments.Selection for lower input current down to 250 A is available upon request. The HCPL-0701 and HCPL-0700 are surface mount devices packaged in an industry standard SOIC-8 footprint. The SOIC-8 does not require through holes in a PCB. This package occupies approximately one-third the foot- print area of the standard dual-in-line package. The lead profile is designed to be compatible with standard surface mount processes. The HCNW139 and HCNW138 are packaged in a widebody encapsulation that provides creepage and clear ance di- mensions suitable for safety approval by regulatory agencies worldwide. Selection Guide 8-Pin DIP Small Outline Widebody (300 Mil) SO-8 (400 mil) Hermetic Dual Single Dual Single and Dual Package Minimum Channel Channel Channel Channel Single Single Input ON Absolute Package Package Package Packages Channel Channel Current Minimum Maximum Package HCPL- HCPL- HCPL- Package (I ) CTR V HCPL- F CC 1 6N139 2731 0701 0731 HCNW139 0.5 mA 400% 18 V 1 6N138 2730 0700 0730 HCNW138 1.6 mA 300% 7 V 1 1 1 1 HCPL-4701 4731 070A 073A 40 A 800% 18 V 1 0.5 mA 300% 20 V 5701 1 5700 1 5731 1 5730 Note: 1. Technical data are on separate Avago publications. Schematic V CC 8 I CC I F 2 ANODE + V F CATHODE I O 3 6 V O 5 GND SHIELD I B 7 V B 2