ACNW261L-500E Broadcom

ACPL-061L, ACPL-C61L and ACNW261L Ultra Low Power 10 MBd Digital CMOS Optocoupler Data Sheet Description Features The ACPL-061L/ACPL-C61L/ACNW261L is an optically Ultra low current I consumption: 1.5 mA max DD coupled optocoupler that combines an AlGaAs light Low input current capability: 1.6 mA min (ACPL-061L), emitting diode and an integrated high gain photo 3 mA min (ACPL-C61L), 4 mA min (ACNW261L) detector addresses the low power need. The optocoupler Available packages: SO-8, Stretched SO-8 and 400 mil consumes extremely low power, at maximum 1.5 mA I DD widebody per channel across temperature. The forward current is as low as 1.6 mA to 4 mA and allows direct current drive by Built-in slew-rate controlled output most microprocessors. Tri-state output with enable pin V E These optocouplers support both 3.3 V and 5 V supply 20 kV/ s minimum Common Mode Rejection (CMR) at voltage with guaranteed AC and DC operational parame- V = 1000 V CM ters from temperature range -40 C to +105 C. The output High Speed: 10 MBd min of the detector IC is a CMOS output. An enable input Guaranteed AC and DC performance over wide allows the detector output to be strobed. The internal temperature: -40 C to +105 C Faraday shield provides a guaranteed common mode transient immunity specification of 20 kV/ s. Safety and Regulatory Approval UL 1577 recognized 3750 Vrms for 1 minute for The CMOS output is slew-rate controlled and is designed ACPL-061L and 5000 Vrms for 1 minute for to allow the rise time and fall time to be controlled over a ACPL-C61L/ACNW261L wide range of the load capacitance. CSA Approval This unique design provides maximum AC and DC circuit IEC/EN/DIN EN 60747-5-5 Approval for Reinforced isolation while achieving TTL/CMOS compatibility. These Insulation optocouplers are suitable for high speed logic interfacing, while consuming extremely low power. Applications 2 Functional Diagram Communication Interface: RS485, CANBus, I C Microprocessor System Interfaces TRUTH TABLE 8 VDD NC 1 (POSITIVE LOGIC) Digital isolation for A/D, D/A conversion LED ENABLE OUTPUT Anode 2 7 VE ON H L 6 VO OFF H H 3 Cathode ON L Z 5 GND NC 4 OFF L Z Shield ON NC L OFF NC H A 0.1 F bypass capacitor must be connected between pins VDD and GND CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD. The components featured in this datasheet are not to be used in military or aerospace applications or environments.Ordering Information ACPL-061L is UL Recognized with 3750 V for 1 minute per UL1577. ACPL-C61L and ACNW261L are UL Recognized rms with 5000 V for 1 minute per UL1577. rms Option UL 1577 Surface Tape & 5000 V / IEC/EN/DIN EN rms Part number (RoHS Compliant) Package Mount Gull Wing Reel 1 Minute rating 60747-5-5 Quantity ACPL-061L -000E SO-8 X 100 per tube -060E X X 100 per tube -500E X X 1500 per reel -560E X X X 1500 per reel ACPL-C61L -000E Stretched X X 80 per tube SO-8 -060E X X X 80 per tube -500E X X X 1000 per reel -560E X X X X 1000 per reel ACNW261L -000E 400 mil X X 42 per tube DIP-8 -300E X X X X 42 per tube -500E X X X X X 750 per reel To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry. Example 1: ACPL-061L-560E to order product of Small Outline SO-8 package in Tape and Reel packaging with IEC/EN/DIN EN 60747-5-5 Safety Approval in RoHS compliant. Option datasheets are available. Contact your Avago sales representative or authorized distributor for information. 2