Data Sheet ACPL-P480 and ACPL-W480 High CMR Intelligent Power Module and Gate Drive Interface Optocoupler Description Features The Broadcom high-speed ACPL-P480/W480 optocoupler Performance specified for common IPM applications over industrial temperature range contains a GaAsP LED, a photo detector, and a Schmitt trigger that eliminates the requirement for external Short maximum propagation delays waveform conditioning circuits. The totem pole output Minimized pulse width distortion (PWD) eliminates the need for a pull-up resistor and allows for a Very high common mode rejection (CMR) direct-drive Intelligent Power Module or gate drive. Hysteresis Propagation delay difference between devices has been Totem pole output (no pull-up resistor required) minimized to maximize inverter efficiency through reduced Available in stretched SO-6 package switching dead time. Package clearance/creepage at 8 mm (ACPL-W480) Safety approvals: Applications UL recognized with 3750V for 1 minute RMS IPM interface isolation (5000V for 1 minute for all ACPL-W480 devices RMS Isolated IGBT/MOSFET gate drive and Option 020 device for ACPL-P480) per UL1577 AC and brushless DC motor drives CSA approved Industrial inverters IEC/EN/DIN EN 60747-5-5 approved with V = IORM General digital iksolation 891V for ACPL-P480 and V = 1140V for peak IORM peak ACPL-W480 Functional Diagram Specifications ANODE 1 66 V CC Wide operating temperature range: 40C to 100C N.C. 2 55 V Maximum propagation delay t /t = 350 ns O PHL PLH Maximum pulse width distortion (PWD) = 250 ns CATHODE 3 44 Ground SHIELD Propagation delay difference: minimum 100 ns, maximum 250 ns Wide operating V range: 4.5V to 20V NOTE: A 0.1-F bypass capacitor must be connected between CC pins 4 and 6. 20 kV/s minimum common mode rejection (CMR) at V = 1000V CM Truth Table (Non-Inverting Logic) CAUTION It is advised that normal static precautions be taken in handling and assembly of this LED V0 component to prevent damage and/or ON HIGH degradation which may be induced by ESD. OFF LOW Broadcom AV02-1305EN June 5, 2020ACPL-P480 and ACPL-W480 Data Sheet High CMR Intelligent Power Module and Gate Drive Interface Optocoupler Ordering Information ACPL-P480 is UL Recognized with 3750V for 1 minute and ACPL-W480 is UL Recognized with 5000V for 1 minute RMS RMS per UL1577. Both are approved under CSA Component Acceptance Notice 5, File CA 88324. Option IEC/EN/DIN EN Part Number RoHS Compliant Package Surface Mount Tape and Reel 60747-5-5 Quantity ACPL-P480 -000E 7 mm Stretched X 100 per tube SO-6 -500E X X 1000 per tube -020E X 100 per tube -520E X X 1000 per tube -060E X X 100 per tube -560E X X X 1000 per tube ACPL-W480 -000E 8 mm Stretched X 100 per tube SO-6 -500E X X 1000 per tube -060E X X 100 per tube -560E X X X 1000 per tube To order, choose a part number from the part number column and combine with the desired option from the option column to form an ordering part number. Example 1: ACPL-P480-560E to order product of Stretched SO-6 package in Tape and Reel packaging with IEC/EN/DIN EN 60747- 5-5 Safety Approval in RoHS compliant. Example 2: ACPL-P480-000E to order product of Stretched SO-6 package in tube packaging and RoHS compliant. Option data sheets are available. Contact your Broadcom sales representative or authorized distributor for information. Solder Reflow Profile The recommended reflow profile is per JEDEC Standard, J-STD-020 (latest revision). Non-halide flux should be used. Regulatory Information The ACPL-P480 and ACPL-W480 are approved by the following organizations: IEC/EN/DIN EN 60747-5-5 (Option 060 only): IEC 60747-5-5: 2007 EN 60747-5-5: 2011 DIN EN 60747-5-5 (VDE 0884-5): 2011-11 UL: ACPL-P480: Approval under UL 1577, component recognition program up to V = 3750V . File E55361. ISO RMS ACPL-W480 and ACPL-P480 (option 020): Approval under UL 1577, component recognition program up to V = ISO 5000V . File E55361. RMS CSA: Approval under CSA Component Acceptance Notice 5, File CA 88324. Broadcom AV02-1305EN 2