HCPL-4504/J454/0454, HCNW4504
High CMR, High Speed Optocouplers
Data Sheet
Lead (Pb) Free
RoHS 6 fully
compliant
RoHS 6 fully compliant options available;
-xxxE denotes a lead-free product
Description Features
Short propagation delays for TTL and IPM applications
The HCPL-4504 and HCPL-0454 contain a GaAsP LED
while the HCPL-J454 and HCNW4504 contain an AlGaAs 15 kV/s minimum Common Mode Transient immu-
LED. The LED is optically coupled to an integrated high nity at V = 1500 V for TTL/load drive
CM
gain photo detector.
High CTR at T = 25C
A
>25% for HCPL-4504/0454
The HCPL-4504 series has short propagation delays and
>23% for HCNW4504
high CTR. The HCPL-4504 series also has a guaranteed
>19% for HCPL-J454
propagation delay difference (t -t ). These features
PLH PHL
Electrical specifications for common IPM applications
make the HCPL-4504 series an excellent solution to IPM
inverter dead time and other switching problems. The TTL compatible
CTR, propagation delay, and CMR are specified both for
Open collector output
TTL and IPM conditions which are provided for ease of
Safety approval:
application. These single channel, diode-transistor opto-
UL recognized
couplers are available in 8-Pin DIP, SO-8, and Widebody
3750 V rms/1min. for HCPL-4504/0454/J454
package configurations. An insulating layer between a
5000 V rms/1min. for HCPL-4504 Option 020 and
LED and an integrated photodetector provide electrical
HCNW4504
insulation between input and output. Separate connec-
CSA approved
tions for the photodiode bias and output-transistor col-
IEC/EN/DIN EN 60747-5-2 approved
lector increase the speed up to a hundred times that of
V = 560 Vpeak for HCPL-0454 Option 060
a conventional phototransistor coupler by reducing the IORM
base collector capacitance. V = 630 Vpeak for HCPL-4504 Option 060
IORM
V = 891 Vpeak for HCPL-J454
IORM
Functional Diagram
V = 1414 Vpeak for HCNW4504
IORM
Applications
8
NC 1 V
CC
Inverter circuits and Intelligent Power Module (IPM)
TRUTH TABLE
interfacing: High Common Mode Transient immunity
ANODE 2 7 NC
LED V
O
(> 10 kV/s for an IPM load/drive) and (t - t )
PLH PHL
ON LOW
CATHODE 3 6 V
Specified (see Power Inverter Dead Time section)
O OFF HIGH
Line receivers: Short propagation delays and low in-
NC 4 5 GND
put-output capacitance
High speed logic ground isolation: TTL/TTL, TTL/
A 0.1 F bypass capacitor between pins 5 and 8 is recommended.
CMOS, TTL/LSTTL
Schematic
Replaces pulse transformers: Save board space and
weight
I
CC
8
V
CC
Analog signal ground isolation: Integrated photode-
tector provides improved linearity over phototransis-
I
F
+ HCPL-4504 Functional Diagram
ANODE
tors
2
V
F
I
O 6
V
O
CATHODE
3
5
SHIELD
GND
CAUTION: It is advised that normal static precautions be taken in handling and assembly
of this component to prevent damage and/or degradation which may be induced by ESD.
HCPL-4504 SchematicOrdering Information
HCPL-0454, HCPL-4504 and HCPL-J454 are UL Recognized with 3750 Vrms for 1 minute per UL1577.
HCNW4504 is UL Recognized with 5000 Vrms for 1 minute per UL1577. HCPL-0454, HCPL-4504, HCPL-J454 and
HCNW4504 are approved under CSA Component Acceptance Notice #5, File CA 88324.
UL 1577
Option
5000 Vrms/
Part RoHS non RoHS Surface Gull Tape 1 Minute IEC/EN/DIN
Number Compliant Compliant Package Mount Wing & Reel rating EN 60747-5-2 Quantity
-000E no option 50 per tube
-300E #300 X X 50 per tube
-500E #500 X X X 1000 per reel
-020E #020 X 50 per tube
300 mil
HCPL-4504 -320E #320 X X X 50 per tube
DIP-8
-520E #520 X X X X 1000 per reel
-060E #060 X 50 per tube
-360E #360 X X X 50 per tube
-560E #560 X X X X 1000 per reel
-000E no option X 50 per tube
-300E #300 X X X 50 per tube
300 mil
HCPL-J454 -400E NA X X X 50 per tube
DIP-8
-500E #500 X X X X 1000 per reel
-600E NA X X X X 750 per reel
-000E no option X 100 per tube
-500E #500 X X 1500 per reel
HCPL-0454 SO-8
-060E #060 X X 100 per tube
-560E #560 X X X 1500 per reel
-000E no option X X 42 per tube
400 mil
HCNW4504 -300E #300 Widebody X X X X 42 per tube
DIP-8
-500E #500 X X X X X 750 per reel
To order, choose a part number from the part number column and combine with the desired option from the option
column to form an order entry.
Example 1:
HCPL-4504-560E to order product of 300 mil DIP Gull Wing Surface Mount package in Tape and Reel packaging
with IEC/EN/DIN EN 60747-5-2 Safety Approval and RoHS compliant.
Example 2:
HCPL-4504 to order product of 300 mil DIP package in Tube packaging and non RoHS compliant.
Option datasheets are available. Contact your Avago sales representative or authorized distributor for information.
Remarks: The notation #XXX is used for existing products, while (new) products launched since July 15, 2001 and
RoHS compliant will use XXXE.
2