HCPL-0534-000E Broadcom

HCPL-250L/050L/253L/053L LVTTL/LVCMOS Compatible 3.3 V Optocouplers (1 Mb/s) Data Sheet Lead (Pb) Free RoHS 6 fully compliant RoHS 6 fully compliant options available -xxxE denotes a lead-free product Features Description 3.3V/5V Dual Supply Voltages These diode-transistor optocouplers use an insulating layer between a LED and an integrated photodetector Low power consumption to provide electrical insulation between input and out- High speed: 1 Mb/s put. Separate connections for the photodiode bias and LVTTL/LVCMOS compatible output-transistor collector increase the speed up to a hundred times that of a conventional photo-transistor Available in 8-pin DIP, SO-8 coupler by reducing the base-collector capacitance. Open collector output These optocouplers are available in an 8-pin DIP and in Guaranteed performance from temperature: an industry standard SO-8 package. The following is a 0C to +70C cross reference table listing the 8-pin DIP part number Safety approval, UL, CSA, IEC/EN/DIN EN 60747-5-2 and the electrically equivalent SO-8 part number. Applications The SO-8 does not requirethrough hole in a PCB. This package occupies approximately one-third the foot- High voltage insulation print area of the standard dual-in-line package. The lead Video signal isolation profile is designed to be compatible with standard sur - face mount processes. Power translator isolation in motor drives Line receivers These optocouplers can be used in LVTTL/LVCMOS or wide bandwidth analog applications. Feedback element in switched mode power supplies The common mode transient immunity of 1000 V/s High speed logic ground isolation LVTTL/LVCMOS minimum to typical at VCM = 10 V guaranteed for these Replaces pulse transformers optocouplers. Replaces slow phototransistor isolators 8-Pin DIP SO-8 Package Functional Diagram HCPL-250L HCPL-050L HCPL250L/HCPL050L HCPL253L/HCPL053L HCPL-253L HCPL-053L 8 1 8 NC 1 V ANODE V CC 1 CC 7 7 ANODE 2 V CATHODE 2 V B 1 O1 6 6 CATHODE 3 V CATHODE 3 V O 2 O2 NC 4 5 GND ANODE 4 5 GND 2 TRUTH TABLE (POSITIVE LOGIC) LED V O ON LOW OFF HIGH A 0.1 F bypass capacitor must be connected between pins 5 and 8. HCPL-250L Functional Diagram CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD. Ordering Information HCPL-250L, HCPL-253L, HCPL-050L and HCPL-053L are UL Recognized with 3750 Vrms for 1 minute per UL1577 and are approved under CSA Component Acceptance Notice 5, File CA 88324. Option Part RoHS non RoHS Surface Gull Tape UL 5000 Vrms/ IEC/EN/DIN Number Compliant Compliant Package Mount Wing & Reel 1 Minute rating EN 60747-5-2 Quantity -000E no option 300 mil DIP-8 50 per tube -300E -300 X X 50 per tube -500E -500 X X X 1000 per reel HCPL-250L -020E -020 X 50 per tube HCPL-253L -320E -320 X X X 50 per tube -520E -520 X X X X 1000 per reel -060E -060 X 50 per tube -360E -360 X X X 50 per tube -560E -560 X X X X 1000 per reel HCPL-050L -000E no option SO-8 100 per tube HCPL-053L -500E -500 X X X 1500 per reel To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry. Example 1: HCPL-253L-560E to order product of 300 mil DIP Gull Wing Surface Mount package in Tape and Reel packaging with IEC/EN/DIN EN 60747-5-2 Safety Approval and RoHS compliant. Example 2: HCPL-253L to order product of 300 mil DIP package in Tube packaging and non RoHS compliant. Option datasheets are available. Contact your Avago sales representative or authorized distributor for information. Remarks: The notation XXX is used for existing products, while (new) products launched since July 15, 2001 and RoHS compliant will use XXXE. 2