HCPL-2201, HCPL-2202, HCPL-2211, HCPL-2212, HCPL-2231, HCPL-2232, HCPL-0201, HCPL-0211, HCNW2201, HCNW2211 Very High CMR, Wide V Logic Gate Optocouplers CC Data Sheet Lead (Pb) Free RoHS 6 fully compliant RoHS 6 fully compliant options available -xxxE denotes a lead-free product Description Features 10 kV/s minimum Common Mode Rejection The HCPL-22XX, HCPL-02XX, and HCNW22XX are optical- (CMR) at V = 1000 V (HCPL-2211/2212/0211/2232, ly-coupled logic gates. The HCPL-22XX, and HCPL-02XX CM HCNW2211) contain a GaAsP LED while the HCNW22XX contains an AlGaAs LED. The detectors have totem pole output Wide operating V range: 4.5 to 20 Volts CC stages and optical receiver input stages with built-in 300 ns propagation delay guaranteed over the full Schmitt triggers to provide logic-compatible waveforms, temperature range eliminat ing the need for additional waveshaping. 5 Mbd typical signal rate A superior internal shield on the HCPL-2211/12, HCPL- Low input current (1.6 mA to 1.8 mA) 0211, HCPL-2232 and HCNW2211 guarantees common Hysteresis mode transient immunity of 10 kV/s at a common Totem pole output (no pullup resistor required) mode voltage of 1000 volts. Available in 8-Pin DIP, SOIC-8, widebody packages Functional Diagram Guaranteed performance from -40C to 85C HCPL-2201/11 Safety approval HCPL-0201/11 HCNW2201/11 HCPL-2202/12 UL recognized -3750 V rms for 1 minute (5000 V 8 8 NC 1 V NC 1 V CC CC rms for 1 minute for HCNW22XX) per UL1577 2 7 V 2 7 NC CSAapproved ANODE O ANODE IEC/EN/DIN EN 60747-5-5 approved with V = 6 NC 6 IORM CATHODE 3 CATHODE 3 V O 630 V (HCPL-2211/2212 Option 060 only) and peak V = 1414 V (HCNW22XX only) 4 5 4 5 NC GND NC GND IORM peak SHIELD SHIELD MIL-PRF-38534 hermetic version available HCPL-2231/32 (HCPL-52XX/62XX) ANODE 1 1 8 V CC TRUTH TABLE Applications (POSITIVE LOGIC) V LED V CATHODE 1 2 7 O O1 Isolation of high speed logic systems ON HIGH OFF LOW Computer-peripheral interfaces CATHODE 2 3 6 V O2 Microprocessor system interfaces 4 5 ANODE 2 GND SHIELD Ground loop elimination Pulse transformer replacement A 0.1 F bypass capacitor must be connected between pins 5 and 8. High speed line receiver Power control systems CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD. The components featured in this datasheet are not to be used in military or aerospace applications or environments.The electrical and switching characteristics of the HCPL-22XX, HCPL-02XX and HCNW22XX are guaranteed from -40C to +85C and a V from 4.5 volts to 20 volts. Low I and wide V range allow compati bil ity with TTL, LSTTL, CC F CC and CMOS logic and result in lower power consump tion compared to other high speed couplers. Logic signals are transmitted with a typical propagation delay of 150 ns. Selection Guide Small- Widebody Minimum CMR Input 8-Pin DIP (300 Mil) Outline SO-8 (400 Mil) Hermetic On- Single Dual Single Single Single and dV/dt Current Channel Channel Channel Channel Dual Channel (V/s) V (V) (mA) Package Package Package Package Packages CM 1,2 1,000 50 1.6 HCPL-2200 HCPL-0201 HCNW2201 HCPL-2201 HCPL-2202 1.8 HCPL-2231 1,2 2,500 400 1.6 HCPL-2219 3 3 5,000 300 1.6 HCPL-2211 HCPL-0211 HCNW2211 HCPL-2212 1.8 HCPL-2232 2 1,000 50 2.0 HCPL-52XX 2 HCPL-62XX Notes: 1. HCPL-2200/2219 devices include output enable/disable function. 2. Technical data for the HCPL-2200/2219, HCPL-52XX and HCPL-62XX are on separate Avago publications. 3. Minimum CMR of 10 kV/s with V = 1000 V can be achieved with input current, I , of 5 mA. CM F Schematic I CC V CC 8 I I O1 F1 1 + V O1 7 V F1 I CC V CC 2 8 SHIELD I I O F 2 + V O V F 3 I O2 3 GND V O2 SHIELD 5 6 V F2 HCPL-2201/02/11/12 + HCPL-0201/11 4 I F2 HCNW2201/11 GND SHIELD 5 HCPL-2231/32 2