HCPL-4504/J454/0454, HCNW4504 High CMR, High Speed Optocouplers Data Sheet Lead (Pb) Free RoHS 6 fully compliant RoHS 6 fully compliant options available -xxxE denotes a lead-free product Description Features Short propagation delays for TTL and IPM applications The HCPL-4504 and HCPL-0454 contain a GaAsP LED while the HCPL-J454 and HCNW4504 contain an AlGaAs 15 kV/s minimum Common Mode Transient immu- LED. The LED is optically coupled to an integrated high nity at V = 1500 V for TTL/load drive CM gain photo detector. High CTR at T = 25C A >25% for HCPL-4504/0454 The HCPL-4504 series has short propagation delays and >23% for HCNW4504 high CTR. The HCPL-4504 series also has a guaranteed >19% for HCPL-J454 propagation delay difference (t -t ). These features PLH PHL Electrical specifications for common IPM applications make the HCPL-4504 series an excellent solution to IPM inverter dead time and other switching problems. The TTL compatible CTR, propagation delay, and CMR are specified both for Open collector output TTL and IPM conditions which are provided for ease of Safety approval: application. These single channel, diode-transistor opto- UL recognized couplers are available in 8-Pin DIP, SO-8, and Widebody 3750 V rms/1min. for HCPL-4504/0454/J454 package configurations. An insulating layer between a 5000 V rms/1min. for HCPL-4504 Option 020 and LED and an integrated photodetector provide electrical HCNW4504 insulation between input and output. Separate connec- CSA approved tions for the photodiode bias and output-transistor col- IEC/EN/DIN EN 60747-5-2 approved lector increase the speed up to a hundred times that of V = 560 Vpeak for HCPL-0454 Option 060 a conventional phototransistor coupler by reducing the IORM base collector capacitance. V = 630 Vpeak for HCPL-4504 Option 060 IORM V = 891 Vpeak for HCPL-J454 IORM Functional Diagram V = 1414 Vpeak for HCNW4504 IORM Applications 8 NC 1 V CC Inverter circuits and Intelligent Power Module (IPM) TRUTH TABLE interfacing: High Common Mode Transient immunity ANODE 2 7 NC LED V O (> 10 kV/s for an IPM load/drive) and (t - t ) PLH PHL ON LOW CATHODE 3 6 V Specified (see Power Inverter Dead Time section) O OFF HIGH Line receivers: Short propagation delays and low in- NC 4 5 GND put-output capacitance High speed logic ground isolation: TTL/TTL, TTL/ A 0.1 F bypass capacitor between pins 5 and 8 is recommended. CMOS, TTL/LSTTL Schematic Replaces pulse transformers: Save board space and weight I CC 8 V CC Analog signal ground isolation: Integrated photode- tector provides improved linearity over phototransis- I F + HCPL-4504 Functional Diagram ANODE tors 2 V F I O 6 V O CATHODE 3 5 SHIELD GND CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD. HCPL-4504 SchematicOrdering Information HCPL-0454, HCPL-4504 and HCPL-J454 are UL Recognized with 3750 Vrms for 1 minute per UL1577. HCNW4504 is UL Recognized with 5000 Vrms for 1 minute per UL1577. HCPL-0454, HCPL-4504, HCPL-J454 and HCNW4504 are approved under CSA Component Acceptance Notice 5, File CA 88324. UL 1577 Option 5000 Vrms/ Part RoHS non RoHS Surface Gull Tape 1 Minute IEC/EN/DIN Number Compliant Compliant Package Mount Wing & Reel rating EN 60747-5-2 Quantity -000E no option 50 per tube -300E 300 X X 50 per tube -500E 500 X X X 1000 per reel -020E 020 X 50 per tube 300 mil HCPL-4504 -320E 320 X X X 50 per tube DIP-8 -520E 520 X X X X 1000 per reel -060E 060 X 50 per tube -360E 360 X X X 50 per tube -560E 560 X X X X 1000 per reel -000E no option X 50 per tube -300E 300 X X X 50 per tube 300 mil HCPL-J454 -400E NA X X X 50 per tube DIP-8 -500E 500 X X X X 1000 per reel -600E NA X X X X 750 per reel -000E no option X 100 per tube -500E 500 X X 1500 per reel HCPL-0454 SO-8 -060E 060 X X 100 per tube -560E 560 X X X 1500 per reel -000E no option X X 42 per tube 400 mil HCNW4504 -300E 300 Widebody X X X X 42 per tube DIP-8 -500E 500 X X X X X 750 per reel To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry. Example 1: HCPL-4504-560E to order product of 300 mil DIP Gull Wing Surface Mount package in Tape and Reel packaging with IEC/EN/DIN EN 60747-5-2 Safety Approval and RoHS compliant. Example 2: HCPL-4504 to order product of 300 mil DIP package in Tube packaging and non RoHS compliant. Option datasheets are available. Contact your Avago sales representative or authorized distributor for information. Remarks: The notation XXX is used for existing products, while (new) products launched since July 15, 2001 and RoHS compliant will use XXXE. 2