HCPL-M700/HCPL-M701 Small Outline, 5 Lead, Low Input Current, High Gain Optocouplers Data Sheet Description Features These small outline, low input current, high gain Surface mountable optocouplers are single channel devices in a five lead Very small, low profile JEDEC registered package outline miniature footprint. They are electrically equivalent Compatible with infrared vapor phase reflow and wave to the following Avago optocouplers: soldering processes High current transfer ratio: 2000% The SO-5 JEDEC registered (MO-155) package outline Low input current capability: 0.5 mA does not require through holes in a PCB. This TTL compatible output: V = 0.1 V package occupies approximately one-fourth the OL footprint area of the standard dual-in-line package. Guaranteed ac and dc performance over temperature: The lead profile is designed to be compatible with 0C to 70C standard surface mount processes. High output current: 60 mA Recognized under the component program of U.L. (file No. These high gain series opto-couplers use a Light E55361) for dielectric withstand proof test voltage of 3750 Emitting Diode and an integrated high gain photo- Vac, 1 minute detector to provide extremely high current transfer Lead free option -000E ratio between input and output. Separate pins for the photodiode and output stage results in TTL Applications compatible saturation voltages and high speed Ground isolate most logic families: TTL/TTL, CMOS/TTL, operation. Where desired the V and V terminals CC O CMOS/CMOS, LSTTL/TTL, CMOS/LSTTL may be tied together to achieve conventional photo- darlington operation. Low input current line receiver EIA RS232C line receiver The HCPL-M701 is for use in CMOS, LSTTL or other Telephone ring detector low power applications. A 400% minimum current ac line voltage status indicator: transfer ratio is guaranteed over a 0-70C operating low input power dissipation range for only 0.5 mA of LED current. Low power systems: ground isolation The HCPL-M700 is designed for use mainly in TTL applications. Current Transfer Ratio is 300% minimum over 0-70C for an LED current of 1.6 mA 1 TTL Unit Load (U.L.) . A 300% CTR enables operation with 1 U.L. out with a 2.2 k pull-up resistor. Selection for lower input currents down to 250 A is available upon request. SO-5 Package Standard DIP SO-8 Package HCPL-M700 6N138 HCPL-0700 HCPL-M701 6N139 HCPL-0701 CAUTION: The small device geometries inherent to the design of this bipolar component increase the components susceptibility to damage from electrostatic discharge (ESD). It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD.Ordering Information HCPL-M700 and HCPL-M701 are UL Recognized with 3750 V for 1 minute per UL1577 and are approved rms under CSA Component Acceptance Notice 5, File CA 88324. Option Part RoHS Non RoHS Surface Gull Tape & Number Compliant Compliant Package Mount Wing Reel Quantity HCPL-M700 -000E No option 100 per tube SO-5 HCPL-M701 -500E 500 X X X 1500 per reel To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry. Example 1: HCPL-M700-500E to order product of Mini-flat Surface Mount 5-pin package in Tape and Reel packaging with RoHS compliant. Example 2: HCPL-M700 to order product of Mini-flat Surface Mount 5-pin package in tube packaging and non RoHS compliant. Option data sheets are available. Contact your Avago sales representative or authorized distributor for information. th Remarks: The notation XXX is used for existing products, while (new) products launched since 15 July 2001 and RoHS compliant option will use -XXXE. Outline Drawing (JEDEC MO-155) ANODE 1 6 V CC MXXX 7.0 0.2 5 V 4.4 0.1 OUT (0.276 0.008) (0.173 0.004) XXX CATHODE 3 4 GND 0.4 0.05 (0.016 0.002) 3.6 0.1* (0.142 0.004) 0.102 0.102 2.5 0.1 0.15 0.025 (0.004 0.004) (0.098 0.004) (0.006 0.001) 7 MAX. 1.27 0.71 BSC MIN. (0.050) (0.028) MAX. LEAD COPLANARITY = 0.102 (0.004) DIMENSIONS IN MILLIMETERS (INCHES) * MAXIMUM MOLD FLASH ON EACH SIDE IS 0.15 mm (0.006) NOTE: FLOATING LEAD PROTRUSION IS 0.15 mm (6 mils) MAX. 2