HLMA-Qx00, HLMA-Px00 HLMT-Px00 and HLMT-Qx00 Subminiature High Performance AlInGaP LED Lamps Data Sheet SunPower Series HLMA-PF00, HLMA-PG00, HLMA-PH00, HLMA-PL00, HLMA-QF00, HLMA-QG00, HLMA-QH00, HLMA-QL00, HLMT-PG00, HLMT-PH00, HLMT-PL00, HLMT-QG00, HLMT-QH00, HLMT-QL00 Description Features Subminiature fl at top package Flat Top Package Ideal for backlighting and light piping applications The HLMX-PXXX fl at top lamps use an untinted, nondif- Subminiature dome package fused, truncated lens to provide a wide radiation pattern Nondiff used dome for high brightness that is neces sary for use in backlighting applica tions. The Wide range of drive currents fl at top lamps are also ideal for use as emitters in light Colors: 590 nm Amber, 605 nm Orange, 615 nm Red- pipe applications. dish-Orange, 622/626 nm Red, and 635 nm Red Dome Packages Ideal for space limited applications Axial leads The HLMX-QXXX dome lamps use an untinted, nondif- fused lens to provide a high luminous inten sity within a Available with lead confi gurations for surface mount narrow radiation pattern. and through hole PC board mounting Lead Confi gurations Technology All of these devices are made by encapsulating LED chips on axial lead frames to form molded epoxy submini- These subminiature solid state lamps utilize one of the ature lamp packages. A variety of package confi guration two newly devel oped aluminum indium gallium phos- options is available. These include special surface mount phide (AlInGaP) LED technologies. The HLMT-Devices lead confi gura tions, gull wing, yoke lead, or Z-bend. Right are especially eff ective in very bright ambient lighting angle lead bends at 2.54 mm (0.100 inch) and 5.08 mm condi tions. The colors 590 nm amber, 605 nm orange, (0.200 inch) center spacing are available for through hole 615 nm reddish-orange, 622/626 nm red, and 635 nm red mounting. For more infor mation refer to Standard SMT are available with viewing angles of 15 for the domed and Through Hole Lead Bend Options for Subminiature devices and 125 for the fl at top devices. LED Lamps data sheet.Device Selection Guide Typ. I Package Viewing Package d V 1 Part Number (nm) (mcd) Description Angle 2 / Outline 2 HLMA-QL00 590 500 Domed, 15 B HLMT-QL00 590 1000 Nondiff used, HLMA-QJ00 605 500 Untinted HLMA-QH00 615 500 HLMT-QH00 615 800 HLMA-QG00 626 500 HLMT-QG00 622 1000 HLMA-QF00 635 500 HLMA-PL00 590 75 Flat Top, 125 A HLMT-PL00 590 150 Nondiff used, HLMA-PJ00 605 75 Untinted HLMA-PH00 615 75 HLMT-PH00 615 120 HLMA-PG00 626 75 HLMT-PG00 622 150 HLMA-PF00 635 75 Absolute Maximum Ratings at T = 25C A Parameter HLMA-xxxx HLMT-xxxx Unit 2 Peak Forward Current 100 100 mA 1,2 Average Forward Current (I = 100 mA) 30 30 mA PEAK 3,5,6 DC Forward Current 50 50 mA Power Dissipation 120 130 mW Reverse Voltage (I = 100 A) 5 V R 5 Transient Forward Current (10 s Pulse) 500 mA Operating Temperature Range 40 to +100 C Storage Temperature Range 55 to +100 C LED Junction Temperature 110 C Lead Soldering Temperature 1.6 mm (0.063 in.) from body 260C for 5 seconds SMT Refl ow Soldering Temperature 260C for 20 seconds Notes: 1. Maximum I at f = 1 kHz. AVG 2. Refer to Figure 5 to establish pulsed operating conditions. 3. Derate linearly as shown in Figure 4. 4. The transient peak current is the maximum non-recurring peak current these devices can withstand without damaging the LED die and wire bonds. Operation at currents above Absolute Maximum Peak Forward Current is not recommended. 5. Drive currents between 10 mA and 30 mA are recommended for best long term performance. 6. Operation at currents below 5 mA is not recommended, please contact your Avago sales representative. 2