Data Sheet HLMA-Qx00, HLMA-Px00, HLMT-Px00, and HLMT-Qx00 Subminiature High Performance AlInGaP LED Lamps Sun Power Series HLMA-PF00, HLMA-PG00, HLMA-PH00, HLMA-PL00, HLMA-QF00, HLMA-QG00, HLMA-QH00, HLMA-QL00, HLMT-PG00, HLMT-PH00, HLMT-PL00, HLMT-QG00, HLMT-QH00, HLMT-QL00 Features Description Subminiature flat top package Flat Top Package Ideal for backlighting and light piping applications Subminiature dome package The HLMX-PXXX flat top lamps use an untinted, Nondiffused dome for high brightness nondiffused, truncated lens to provide a wide radiation Wide range of drive currents pattern that is necessary for use in backlighting applications. Colors: The flat top lamps are also ideal for use as emitters in light 590-nm Amber pipe applications. 605-nm Orange 615-nm Reddish-Orange Dome Packages 622/626-nm Red 635-nm Red The HLMX-QXXX dome lamps use an untinted, nondiffused Ideal for space-limited applications lens to provide a high luminous intensity within a narrow radiation pattern. Axial leads Available with lead configurations for surface mount and through hole PC board mounting Lead Configurations All of these devices are made by encapsulating LED chips Technology on axial lead frames to form molded epoxy subminiature These subminiature solid state lamps use one of the two lamp packages. A variety of package configuration options newly developed aluminum indium gallium phosphide are available. These include special surface mount lead (AlInGaP) LED technologies. The HLMT-devices are configurations, gull wing, yoke lead, or Z-bend. Right angle especially effective in very bright ambient lighting lead bends at 2.54 mm (0.100 in.) and 5.08 mm (0.200 in.) conditions. The colors 590-nm amber, 605-nm orange, center spacing are available for through hole mounting. For 615-nm reddish-orange, 622/626-nm red, and 635-nm red more information, refer to the Standard SMT and Through are available with viewing angles of 15 for the domed Hole Lead Bend Options for Subminiature LED Lamps Data devices and 125 for the flat top devices. Sheet. Broadcom AV02-0309EN March 20, 2020HLMA-Qx00, HLMA-Px00, HLMT-Px00, and HLMT-Qx00 Data Sheet Subminiature High Performance AlInGaP LED Lamps Device Selection Guide Package (nm) Typ. I (mcd) Part Number Viewing Angle 2 Package Outline d V Description HLMA-QL00 590 500 Domed, Nondiffused, 15 B Untinted HLMT-QL00 590 1000 HLMA-QJ00 605 500 HLMA-QH00 615 500 HLMT-QH00 615 800 HLMA-QG00 626 500 HLMT-QG00 622 1000 HLMA-QF00 635 500 HLMA-PL00 590 75 Flat Top, 125 A Nondiffused, Untinted HLMT-PL00 590 150 HLMA-PJ00 605 75 HLMA-PH00 615 75 HLMT-PH00 615 120 HLMA-PG00 626 75 HLMT-PG00 622 150 HLMA-PF00 635 75 Absolute Maximum Ratings at T = 25C A Parameter HLMA-xxxx HLMT-xxxx Units a 100 100 mA Peak Forward Current a, b 30 30 mA Average Forward Current (I = 100 mA) PEAK c, d, e 50 50 mA DC Forward Current Power Dissipation 120 130 mW Reverse Voltage (I = 100 A) 5 V R f 500 mA Transient Forward Current (10 s Pulse) Operating Temperature Range 40 to +100 C Storage Temperature Range 55 to +100 C LED Junction Temperature 110 C Lead Soldering Temperature (1.6 mm (0.063 in.) from body) 260C for 5 seconds SMT Reflow Soldering Temperature 260C for 20 seconds a. See Figure 7 and Figure 8 to establish pulsed operating conditions. b. Maximum I at f = 1 kHz. AVG c. Derate linearly as shown in Figure 6. d. Drive currents between 10 mA and 30 mA are recommended for best long term performance. e. Operation at currents below 5 mA is not recommended contact your Broadcom sales representative. f. The transient peak current is the maximum non-recurring peak current these devices can withstand without damaging the LED die and wire bonds. Operation at currents above Absolute Maximum Peak Forward Current is not recommended. Broadcom AV02-0309EN 2