G21205501700 Carlo Gavazzi

Input-Module for Elevators Du line Type G 2120 5501 700, G 2120 5502 700 Fieldbus Installationbus 8-channel transmitter 8 contact or NPN transistor inputs (G2120 5501) or 8 voltage or PNP transistor inputs (G2120 5502) Open printed circuit board Bracket for DIN-rail mounting available LED-indications for supply and Dupline carrier DC or Dupline supplied Channel coding by GAP 1605 Product Description Ordering Key G 2120 5501 700 Dupline transmitter design - mounting, operation and Type: Dupline ed to be a part of the maintenance without re - Open PCB Dupline concept for push quire ment of any special Input-Module buttons and lamps in eleva- tools or programming. Number of I/Os tors. Installer friendly Input type DC-supply Type Selection Supply Ordering no. Ordering no. 8 contact or NPN transistor inputs 8 voltage or PNP transistor input 10-30 VDC G 2120 5501 700 G 2120 5502 700 Input Specifications Type G2120 5501 Supply Specifications (cont.) Inputs 8 contacts or NPN-transistors Current consumption Open loop voltage 8.0 VDC When Dupline supplied 0.9 mA Short-circuit current 17A Transient protection voltage 800 V Start peak current 20mA Insultation voltage: Contact resistance 100 Supply - Dupline None Max voltage drop 1V Supply - Outputs None Cable length 3m Response time 156 ms 128 channels General Specifications Input pulse prolongation Typ. 0.5 s Power ON delay Typ. 2 s Indication for Input Specifications Type G2120 5502 Supply ON LED, green Dupline carrier LED, yellow (No Inputs 8 voltage or PNP-transistors indication when Dupline Input current < 2mA ( 24V) supplied) Start peak current 20 mA Environment Input voltage ON > 9V Operating temperature -20 to +50C (-4 to +122F) Input voltage OFF < 1V Storage temperature -50 to +85C (-58 to +185F) Cable length 3m Humidity (non-condensing) 20 - 80% Response time 156 ms 128 channels) Mechanical resistance Input pulse prolongation Typ. 0.5 s Shock 15 G (11 ms) Vibration 2 G (6 to 55 Hz) Supply Specifications Dimensions Open PCB 72,3 x 59 mm 4 pcs. of nylon PA6 snap Power supply DC types Installation cat III (IEC 60664) locks are included for Operational voltage (V ) 10-30 VDC (ripple included) DD In mounting the PCB in 4.8 Ripple 3 V holes Reverse polarity protection Yes Power dissipation 0.5 W Weight 50 g Current consumption 20 mA Specifications are subject to change without notice (01.02.2007) 1 Dupline is a registered trademark. A product of the CARLO GAVAZZI GroupG 2120 550. 700 Du line Fieldbus Installationbus Wiring Diagrams G2120 5501 G2120 5502 Dup (Dupline S) Dup (Dupline S) GND GND Pow (Supply input) Pow (Supply input) DC+ DC+ I1 I1 I2 I2 I3 I3 I4 I4 I5 I5 I6 I6 I7 I7 I8 I8 Pin Allocation Mode of Operation Connect the DC supply volt- ON/OFF-signal that is Pin Input/Output age to the system through a applied to the input of the G 2196 000X 700 Master module is associated to the Dup Dupline Signal Module, which also performs address given to that input. Gnd Dup. + Supply Gnd the channel generator func- An input pulse stretcher (only Pow Supply In tion and the RS485 commu- G 2201 5501) is used on DC+ DC Out nication link to the elevator every input to assure that the I1 Input 1 controller (please refer to the changes of input signals I2 Input 2 data sheet for G2196.. for (even extremely short ones) I3 Input 3 details). are communicated by the I4 Input 4 Every Input is given its indi- system. I5 Input 5 vidual address with the cod- No LED indication for Supply I6 Input 6 ing unit GAP 1605 (Please and Line when Dupline sup- I7 Input 7 refer to the respective plied. I8 Input 8 datasheet for details). The Accessories Aluminum bracket for DIN mounting (Vertical) 8047-bracket PVC bracket for DIN mounting (Horisontal) ELEVAT-Bracket DIN-rail FMD 411 2 Specifications are subject to change without notice (01.02.2007) Dupline is a registered trademark. A product of the CARLO GAVAZZI Group Supply Line CHANNEL PROGRAM PLUG Supply Line CHANNEL PROGRAM PLUG