G21305521700 Carlo Gavazzi

Output-Module for Elevators Du line Type G 2130 55.1 700 Fieldbus Installationbus 8 NPN- or PNP-transistor outputs for control of floor-indicators Open printed circuit board Bracket for DIN-rail mounting available LED-indications for supply and Dupline carrier 3-wire system with Dupline and DC-supply through G 2196 0000 700 Channel coding by GAP 1605 Product Description Ordering Key G 2130 5521 700 Module with 8 NPN- or PNP- in an elevator is connected to Type: Dupline transistor outputs for direct the same 3 wires for bus- Open PCB interface to elevator floor communication with the con- Output-Module indicators. The 8 outputs can trol system and DC-power- Number of I/Os either be connected to the 8 supply for the lamps/LEDs. Output type inputs of intelligent floor indi- Installer friendly mounting, DC-supply cators which are controlled operation and maintenance by bit-combinations or they without requirement of any can be used to drive LED- special tools or programm- segments directly. All modules ing. Type Selection Supply Ordering no. Ordering no. NPN-outputs PNP-outputs 10-30 VDC G 2130 5511 700 G 2130 5521 700 Output Specifications General Specifications Outputs 8 PNP-transistors Power ON delay Typ. 2 s Output voltage drop 2.0 V Indication for Current per output 100 mA Supply ON LED, green Total load capability (01..08) 500 mA Dupline carrier LED, yellow Reverse polarity protection Yes Environment Short-circuit protection None Operating temperature -20 to +50C (-4 to +122F) Built-in protective diodes Yes Storage temperature -50 to +85C (-58 to +185F) Off-state leakage current 200 A Humidity (non-condensing) 20 - 80% Response time 1 pulse train Mechanical resistance (136 ms 128 channels) Shock 15 G (11 ms) Vibration 2 G (6 to 55 Hz) Dimensions Open PCB 74 x 59 mm Supply Specifications 4 pcs. of nylon PA6 snap locks are included for mount- Power supply Overvoltage cat. III (IEC 60664) ing the PCB in 4.8 holes Rated operational voltage (V ) 10-30 VDC (ripple included) in Ripple 3 V Weight 50 g Reverse polarity protection Yes Current consumption 45 mA Power dissipation 1 W Inrush current 1 A Transient protection voltage 800 V Dielectric voltage Supply - Dupline None Supply - Outputs None Specifications are subject to change without notice (29.04.03) 1 Dupline is a registered trademark. A product of the CARLO GAVAZZI GroupG 2130 55.1 700 Du line Fieldbus Installationbus Wiring Diagrams Dup (Dupline S) Dup (Dupline S) GND GND POW (Supply input) POW (Supply input) DC + DC + O1 O1 O2 O2 O3 O3 O4 O4 O5 O5 O6 O6 O7 O7 O8 O8 Pin Allocation Mode of Operation The output unit uses three 8 out of the 128 available Terminal Input/Output wires for the communication Dupline adresses should be with all the other I/O-units of reserved to control the floor- DUP Dupline signal an installation, for the sup- indicators. Since all the indic- GND Dupline + supply GND ply of the I/O-units and for ators must show the same POW Supply IN the loads connected to the value, the output modules DC + DC for output loads outputs of the units. This can all be coded to read the O 1 Output 1 implies, that the common same adresses. This implies O 2 Output 2 of the communication signal that only 8 adresses will be O 3 Output 3 is identical to the minus of occupied for floor indication O 4 Output 4 the supply. no matter how many indic- O 5 Output 5 ators are installed. O 6 Output 6 The DC supply voltage must O 7 Output 7 connect to the system The output status of all out- O 8 Output 8 through a G 2196 0000 700, puts of an output unit may which also performs the be predefined for cases like channel generator function loss of power and loss of and the RS485 communica- communication. Please refer Accessories tion link to the elevator con- to the paragraph Output troller (please refer to the status setting of the data Aluminium bracket for data sheet for G2196 0000 sheet for the GAP 1605 to DIN-mounting 8047- bracket 700 for details). change the default setting DIN-rail FMD 411 (all outputs OFF). 2 Specifications are subject to change without notice (28.09.99) Dupline is a registered trademark. A product of the CARLO GAVAZZI Group G 21305511... Supply LIne Channel program plug Supply G 21305521... LIne Channel program plug