G21405520700 Carlo Gavazzi

I/O-Module for Elevators Du line Type G 2140 55.0 700 Fieldbus Installationbus 4 push-button inputs 4 PNP- or NPN-transistor outputs Open printed circuit board Bracket for DIN-rail mounting available LED-indications for supply and Dupline carrier DC-supply 3-wire system with Dupline and supply of module and output load through G 3485 0000 700 Channel coding by GAP 1605 Product Description Ordering Key G 2140 5520 700 Direct interface to the I/Os of Only 3-wires needed to con- Type: Dupline elevator floor stations, lift-car nect any number of I/O-units Open PCB signals and lift controls. The (including the DC-supply for I/O-module input pulses are prolonged to the output load). Installer- Number of I/Os 0.5 s to ensure transfer of friendly mounting, operation I/O-type fast pushbutton activations. and maintenance without re- DC-supply Due to the small size of the quirements for any special module it can be integrated tools or programming. into most pushbutton panels. Type Selection Supply Ordering no. Ordering no. NPN-outputs PNP-outputs 10-30 VDC G 2140 5510 700 G 2140 5520 700 Output Specifications G 2140 5510 700 G 2140 5520 700 Outputs 4 NPN-transistors 4 PNP-transistors Output voltage drop 1.2 V Output voltage Typ. V -2.0 V in V -2.8 V in Current pr. output 200 mA 200 mA Max. total load 500 mA 500 mA Short circuit protection None None Built-in protective diodes Yes Yes Off-state leakage current 100 A 200 A Response time 1 pulse train (136 ms 128 ch.) 1 pulse train (136 ms 128 ch.) Input Specifications Supply Specifications Inputs 4 contacts or Power supply Overvoltage cat. III (IEC 60664) NPN-transistor Rated operational voltage (V ) 10-30 VDC (ripple included) in Open loop voltage 8.0 VDC Ripple 3 V Short circuit current 180 A Reverse polarity protection Yes Start peak current 7 mA Current consumption 20 mA Contact resistance 100 Power dissipation 1 W Cable length 3 m Inrush current 1 A Transient protection voltage 800 V Transmission delay Dielectric voltage Input OFF - ON 20 ms + 1 pulse train Supply - Dupline None Input ON - OFF 550 ms Supply - Inputs None Supply - Outputs None Specifications are subject to change without notice (29.04.03) 1 Dupline is a registered trademark. A product of the CARLO GAVAZZI GroupG 2140 55.0 700 Du line Fieldbus Installationbus General Specifications Pin Allocation Power ON delay Typ. 2 s Terminal Input/Output Indication for Supply ON LED, green DUP Dupline signal Dupline carrier LED, yellow GND Dupline + supply GND +24 IN Supply IN Environment +24 OUT DC for output loads Operating temperature -20 to +50C (-4 to +122F) I 1 Input 1 Storage temperature -50 to +85C (-58 to +185F) I 2 Input 2 Humidity (non-condensing) 20 - 80% I 3 Input 3 Mechanical resistance I 4 Input 4 Shock 15 G (11 ms) O 1 Output 1 Vibration 2 G (6 to 55 Hz) O 2 Output 2 Dimensions Open PCB 74 x 59 mm O 3 Output 3 4 pcs. of nylon PA6 snap O 4 Output 4 locks are included for mount- ing the PCB in 4.8 holes Weight 100 g Accessories Aluminium bracket for DIN mounting 8047 - bracket DIN-rail FMD 411 Mode of Operation The I/O-units use three wires munication link to elevator address given to that input. assure that the changes of for the communication with controller (please refer to the Any output of an I/O-unit input signals (even extreme- all the other I/O-units of an data sheet for G 2196 0000 that is given the identical ly short ones) are communi- installation, for the supply of 700 for details). address will now follow that cated by the system. the I/O-units and for the input signal and switch its loads connected to the out- Each I/O-unit has 4 inputs output signal ON or OFF. The output status of all out- puts of the units. This (NPN/contact) and 4 outputs This means that a signal puts of an I/O-unit may be implies, that the common (NPN or PNP). Every input which is input at one loca- pre-defined for cases like of the communication signal an output is given its indi- tion (for example as an out- loss of power and loss of is identical to the minus of vidual address with the cod- put from the lift controller) communication. Please refer the supply. The DC-supply ing unit GAP1605 (please may be output wherever to the paragraph Output voltage must connect to the refer to the respective data required and as many times status setting of the data system through a G 2196 sheet for details). The as required. sheet for the GAP 1605 to 0000 700, which also per- ON/OFF-signal that is change the default setting forms the channel generator applied to the input of an An input pulse stretcher is (all outputs OFF). function and the RS485 com- I/O-unit is associated to the used on every input to Wiring Diagrams 2 Specifications are subject to change without notice (28.09.99) Dupline is a registered trademark. A product of the CARLO GAVAZZI Group