Remote Transceiver Du line Type G 8840 5549 Fieldbus Installationbus Small sized transceiver Output load: 8 A/24 VDC Powered via Dupline Address coding by GAP 1605 3 contact inputs 1 tamper module monitoring channel Product De scrip tion Ordering Key G 8840 5549 The Dupline decentral trans- installation concept featuring Type: Dupline ceiver has a build-in SPDT a separate power and signal Housing relay for control of a load of (control) bus. The compact Transceiver up to 8 A/24 VDC. The modu- size of the module makes it No. of channels/in- and outputs le is especially designed for possible to fit it in a cell door Output type use in prison applications application. where it allows a flexible Type Selection Ordering no. 5 channels 8 A/24 VDC G 8840 5549 Output Spec i fi ca tions Supply Spec i fi ca tions Output 1 SPDT relay Supplied by Dupline Contact ratings (Ag/Ni 90/10 ) (micro gap) Normal consumption 1.6 mA Resistive load 8 A/24 VDC Charge consumption 3.1 mA (for max 1 s after 6 Mechanical lifetime > 2x10 operations relay state change) 6 Electrical lifetime > 1x10 operations/24 VDC 2A Power-on delay Typ. 2 s 5 > 1x10 operations/24 VDC 8A Power-off delay 1 s Minimum load (recommended) 10 mA/12 V Operating frequency 60 operations/minute Response time 1 pulse train Input Spec i fi ca tions General Spec i fi ca tions Inputs 3 contacts + one tamper Environment channel (I/O 5-8) Pollution degree 3 (IEC 60664) Open loop voltage 2 to 3 VDC Operation temperature 0 to +50C (32 to 122F) Short-circuit current 25 A Storage temperature -50 to +85C (-58 to 185F) Operating time for signal1 1 pulse train + 10 ms Humidity (non-condensing) 20 to 80% Operating time for signal0 1 pulse train + 110 ms Housing Contact resistance 1 k Material Noryl GFN 1, black Cable length 3 m Dimensions (h x w x d) 26 x 39 x 17 mm Dielectric Voltage Inputs - Dupline None Inputs - Output 200 VAC (rms) Dupline - Output 200 VAC (rms) Specifications are subject to change without notice (12.06.2007) 1 Dupline is a registered trademark. A product of the CARLO GAVAZZI GroupG 8840 5549 Du line Fieldbus Installationbus Mode of Operation Wire Connections The in- and output addresses Tamper channel: If a chan- Bus: White = Dupline signal and fail-polarity may be nel is programmed on in/out Black = Dupline GND coded by means of the code 8, it will be transmitted as Output: Brown - Blue = Relay contact-set NC programmer GAP 1605, with long as the module is conne- Brown - Orange = Relay contact-set NO GAP-THP-CAB cable. cted to Dupline. 2 Bus wires: 2 x 0.75 mm , Upon loss of the Dupline 250 V isolation, single core, 150 mm carrier, the output goes to the 2 Output wires: 3 x 1.5 mm , predefined fail-polarity. 250 V isolation, single core, 150 mm The three contact inputs are 2 located on in/out 5, 6 and 7 Input wires: 3 x 0.25 mm , on the GAP 1605. Multi core, 150 mm Wiring Diagram Channel Configuration On GAP 1605 the in/out configuration is as follows: S In/out 1: Relay output. In/out 5: Contact input 1. Green wire. Contact White Black input: In/out 6: Contact input 2. Yellow wire. Green Orange 1 In/out 7: Contact input 3. Violet wire. Yellow Brown 2 In/out 8: Tamper channel (built-in) Violet Blue 3 SPDT Relay Output Dimensions 39 2 Specifications are subject to change without notice (12.06.2007) Dupline is a registered trademark. A product of the CARLO GAVAZZI Group 17 26