CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS Surface Mount
@Super low ESR, impedance and high heat resistance have been obtained by using
conductive polymer as electrolyte.
(ESR and rated ripple current values are improved from PXA series.)
@Rated voltage range : 2.5 to 16Vdc, Capacitance range : 27 to 470MF
@Case size range : F5B5.7L to F8B6.7L
@Suitable for DC-DC converters, voltage regulators and decoupling applications used to
computer motherboards etc.
@RoHS Compliant
?SPECIFICATIONS
Items Characteristics
Category
-55 to +105C
Temperature Range
Rated Voltage Range 2.5 to 16Vdc
Capacitance Tolerance P20% (M) (at 20C, 120Hz)
Surge Voltage Rated voltage(V)B1.15 (at 105C)
Leakage Current I=0.2CV (max.)
I : Max. leakage current (MA), C : Nominal capacitance (MF), V : Rated voltage (Vdc) (at 20C after 2 minutes)
Dissipation Factor
0.12 max.
(tane)
(at 20C, 120Hz)
Low Temperature
Z(-25C)/Z(+20C)[1.15
Characteristics
(Max. Impedance Ratio) Z(-55C)/Z(+20C)[1.25
(at 100kHz)
Endurance The following specifications shall be satisfied when the capacitors are restored to 20C after the rated voltage is applied for 1,000 hours
at 105C.
Appearance No significant damage
Capacitance change [P20% of the initial value
DF (tanE) [150% of the initial specified value
ESR [150% of the initial specified value
Leakage current [The initial specified value
Bias Humidity The following specifications shall be satisfied when the capacitors are restored to 20C after subjecting them to the DC rated voltage at
60C, 90 to 95% RH for 500 hours.
Appearance No significant damage
Capacitance change [P20% of the initial value
DF (tanE) [150% of the initial specified value
ESR [150% of the initial specified value
Leakage current [The initial specified value
Surge Voltage The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105C for 30 seconds
through a protective resistor(R=1kO) and discharge for 5 minutes 30 seconds.
Appearance No significant damage
Capacitance change [P20% of the initial value
DF (tanE) [150% of the initial specified value
ESR [150% of the initial specified value
Leakage current [The initial specified value
Failure Rate 1% per 1,000 hours maximum (Confidence level 60% at 105C)
*Note : If any doubt arises, measure the leakage current after following voltage treatment.
Voltage treatment : DC rated voltage are applied to the capacitors for 120 minutes at 105C.
?DIMENSIONS [mm] ?MARKING
@Terminal Code : A
EX) 4V220MF
W
C28M
220
Size code fD L A B C W P
V
4
E60 5 5.7 5.3 5.3 5.9 0.5 to 0.8 1.4
F60 6.3 5.7 6.6 6.6 7.2 0.5 to 0.8 1.9
H70 8 6.7 8.3 8.3 9.0 0.7 to 1.1 3.1
0.3max.
AP0.2
LP0.3
?PART NUMBERING SYSTEM
132645178910 11213 14 15 16 17 18
A P X C A A A A R A A A A M A A A G
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 27MF:270,100MF:101)
Taping code
Terminal code
Voltage code (ex. 6.3V:6R3,10V:100)
Series code
Category Please refer toA guide to global code (conductive polymer type
(1/2) CAT. No. E1001F
FDP0.5
BP0.2
P
CP0.2CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS Surface Mount
?STANDARD RATINGS
Rated ripple current
ESR(momax/20c)
WV(Vdc) Cap(mF) Size code (mArms/100k to 300kHz) Part No.
100kHz 300kHz(Ref. value) -55 to +105c
180 E60 30 22 2,000 APXC2R5ARA181ME60G
2.5 270 F60 20 18 2,700 APXC2R5ARA271MF60G
470 H70 17 16 3,420 APXC2R5ARA471MH70G
150 E60 30 22 2,000 APXC4R0ARA151ME60G
4 220 F60 21 19 2,640 APXC4R0ARA221MF60G
330 H70 18 17 3,300 APXC4R0ARA331MH70G
100 E60 35 26 1,780 APXC6R3ARA101ME60G
6.3 180 F60 22 19 2,580 APXC6R3ARA181MF60G
220 H70 18 17 3,300 APXC6R3ARA221MH70G
56 E60 40 31 1,660 APXC100ARA560ME60G
10 82 F60 23 21 2,400 APXC100ARA820MF60G
150 H70 20 19 3,160 APXC100ARA151MH70G
27 E60 45 35 1,570 APXC160ARA270ME60G
16 39 F60 25 23 2,300 APXC160ARA390MF60G
82 H70 25 23 2,830 APXC160ARA820MH70G
(2/2) CAT. No. E1001F