CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS Surface Mount TM NPCAP -PXDSeries Super low ESR, impedance and high heat resistance have been obtained by using con- ductive polymer as electrolyte. For automobile modules and other high temperature applications PXD Endurance : 125 2,000 hours Rated voltage range : 2.5 to 10Vdc, Capacitance range : 47 to 470F Longer life Solvent resistant type (see PRECAUTIONS AND GUIDELINES) RoHS2 Compliant PXH Halogen Free AEC-Q200 compliant : Please contact Chemi-Con for more details, test data, information. SPECIFICATIONS Items Characteristics Category -55 to +125 Temperature Range Rated Voltage Range 2.5 to 10Vdc Capacitance Tolerance 20% (M) (at 20, 120Hz) Leakage Current Shall not exceed values shown in STANDARD RATINGS. *Note (at 20 after 2 minutes) Dissipation Factor 0.12 max. (tan ) (at 20, 120Hz) Low Temperature Z(-25)/Z(+20)1.15 Characteristics Z(-55)/Z(+20)1.25 (at 100kHz) (Max. Impedance Ratio) Endurance The following specications shall be satised when the capacitors are restored to 20 after the rated voltage is applied for 2,000 hours at 125. Appearance No signicant damage Capacitance change 20% of the initial value D.F. (tan) 200% of the initial specied value ESR 200% of the initial specied value Leakage current The initial specied value Bias Humidity The following specications shall be satised when the capacitors are restored to 20 after subjecting them to the DC rated voltage at 60, 90 to 95% RH for 1,000 hours. Appearance No signicant damage Capacitance change 20% of the initial value D.F. (tan) 150% of the initial specied value ESR 150% of the initial specied value Leakage current The initial specied value Surge Voltage The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specied at 125 for 30 seconds through a protective resistor(R=1k) and discharge for 5 minutes 30 seconds. Rated voltage (Vdc) 2.5 6.3 10 Surge voltage (Vdc) 2.9 7.2 12 Appearance No signicant damage Capacitance change 20% of the initial value D.F. (tan) 150% of the initial specied value ESR 150% of the initial specied value Leakage current The initial specied value Soldering Heat The following specications shall be satised when the solder temperature is reduced back to 20C to measure dip resistance after soldering has been performed under the recommended soldering conditions. Appearance No signicant damage Capacitance value Within the specied tolerance range D.F. (tan) The initial specied value ESR The initial specied value Leakage current The initial specied value (Voltage treatment) Failure Rate 0.5% per 1,000 hours maximum (Condence level 60% at 125) *Note : If any doubt arises, measure the leakage current after the following voltage treatment. Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 125. DIMENSIONS mm MARKING EX) 10V330F Terminal Code : A W D22A 330 Size code D L A B C W P V 10 E61 5 5.8 5.3 5.3 5.9 0.5 to 0.8 1.4 F61 6.3 5.8 6.6 6.6 7.2 0.5 to 0.8 1.9 H70 8 6.7 8.3 8.3 9.0 0.7 to 1.1 3.1 J80 10 7.7 10.3 10.3 11.0 0.7 to 1.1 4.5 0.3max. A0.2 L0.3 Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications. CAT. No. E1001U D0.5 B0.2 P C0.2CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS Surface Mount TM NPCAP -PXDSeries PART NUMBERING SYSTEM 1 2 3 4 5 6 78 9 10 11 12 13 14 15 16 17 18 A PXD A RA M G Supplement code Size code Capacitance tolerance code Capacitance code (ex. 47F:470,100F:101) Taping code Terminal code Voltage code (ex. 6.3V:6R3,10V:100) Series code Category Please refer toProduct code guide (conductive polymer type STANDARD RATINGS Rated ripple current WV Cap Leakage current ESR (mArms/100kHz) Size code Part No. (Vdc) (F) (A max./after 2min.) (m max./20 , 100k to 300kHz) *1 *1 -55 Tx +105 +105 Tx +125 120 E61 60.0 40 1,450 650 APXD2R5ARA121ME61G 2.5 220 F61 110 30 2,500 770 APXD2R5ARA221MF61G 56 E61 70.5 45 1,380 600 APXD6R3ARA560ME61G 100 F61 126 35 2,400 720 APXD6R3ARA101MF61G 6.3 220 H70 277 30 3,020 960 APXD6R3ARA221MH70G 470 J80 592 25 3,500 1,100 APXD6R3ARA471MJ80G 47 E61 94.0 50 1,270 550 APXD100ARA470ME61G 56 F61 112 40 2,250 680 APXD100ARA560MF61G 10 150 H70 300 35 2,800 880 APXD100ARA151MH70G 330 J80 660 25 3,500 1,100 APXD100ARA331MJ80G *1Tx : Ambient temperature RATED RIPPLE CURRENT MULTIPLIERS Frequency Multipliers Frequency Hz 120 1k 10k 50k 100k to 500k SMD type 0.05 0.30 0.55 0.70 1.00 Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications. CAT. No. E1001U