CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS Surface Mount TM NPCAP -PXTSeries Super low ESR, impedance and high heat resistance have been obtained by using conductive polymer as electrolyte. High moisture resistance, Bias Humidity: 1,000 hours at 85, 85%RH Rated voltage range: 2.5 to 16Vdc, Capacitance range: 100 to 820F PXN Case size range :55.8L to6.37.7L Suitable for DC-DC converters, voltage regulators and decoupling applications used on Higher ripple computer motherboards etc. Solvent resistant type (see PRECAUTIONS AND GUIDELINES) RoHS2 Compliant PXT Halogen Free SPECIFICATIONS Items Characteristics Category -55 to +105 Temperature Range Rated Voltage Range 2.5 to 16Vdc Capacitance Tolerance 20% (M) (at 20, 120Hz) Leakage Current Shall not exceed values shown in STANDARD RATINGS. *Note (at 20 after 2 minutes) Dissipation Factor 0.12 max. (tan ) (at 20, 120Hz) Low Temperature Z(-25)/Z(+20)1.15 Characteristics Z(-55)/Z(+20)1.25 (at 100kHz) (Max. Impedance Ratio) Endurance The following specications shall be satised when the capacitors are restored to 20 after the rated voltage is applied for 15,000 hours at 105. Appearance No signicant damage Capacitance change 20% of the initial value D.F. (tan) 150% of the initial specied value ESR 150% of the initial specied value Leakage current The initial specied value Bias Humidity The following specications shall be satised when the capacitors are restored to 20 after subjecting them to the DC rated voltage at 8585% RH for 1,000 hours. Appearance No signicant damage Capacitance change 30% of the initial value D.F. (tan) 200% of the initial specied value ESR 200% of the initial specied value Leakage current The initial specied value Surge Voltage The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specied at 105 for 30 seconds through a protective resistor(R=1k) and discharge for 5 minutes 30 seconds. Rated voltage (Vdc) 2.5 4.0 6.3 10 16 Surge voltage (Vdc) 2.9 4.6 7.2 12 18 Appearance No signicant damage Capacitance change 20% of the initial value D.F. (tan) 150% of the initial specied value ESR 150% of the initial specied value Leakage current The initial specied value Soldering Heat The following specications shall be satised when the solder temperature is reduced back to 20C to measure dip resistance after soldering has been performed under the recommended soldering conditions. Appearance No signicant damage Capacitance value Within the specied tolerance range D.F. (tan) The initial specied value ESR The initial specied value Leakage current The initial specified value (Voltage treatment) Failure Rate 0.5% per 1,000 hours maximum (Condence level 60% at 105) *Note : If any doubt arises, measure the leakage current after the following voltage treatment. Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105. DIMENSIONS mm MARKING EX) 2.5V390F Terminal Code : A W T69A Size Code D L A B C W P 390 E61 5 5.8 5.3 5.3 5.9 0.5 to 0.8 1.4 V 2.5 F61 6.3 5.8 6.6 6.6 7.2 0.5 to 0.8 1.9 F80 6.3 7.7 6.6 6.6 7.2 0.5 to 0.8 1.9 0.3max. A0.2 L0.3 Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications. CAT. No. E1001U D0.5 B0.2 P C0.2CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS Surface Mount TM NPCAP -PXTSeries PART NUMBERING SYSTEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 A PXT A RA M G Supplement code Size code Capacitance tolerance code Capacitance code (ex. 100F:101, 390F:391) Taping code Terminal code Voltage code (ex. 2.5V:2R5, 10V:100) Series code Category Please refer toProduct code guide (conductive polymer type STANDARD RATINGS WV Cap Size Leakage current ESR Rated ripple current Part No. (Vdc) (F) code (A max./after 2min.) (m max./20 , 100k to 300kHz) (mArms/105 , 100kHz) 330 E61 700 26 2,350 APXT2R5ARA331ME61G 390 E61 700 26 2,350 APXT2R5ARA391ME61G 2.5 390 F61 700 26 2,600 APXT2R5ARA391MF61G 560 F61 700 26 2,600 APXT2R5ARA561MF61G 820 F80 1,020 22 2,850 APXT2R5ARA821MF80G 270 E61 700 26 2,350 APXT4R0ARA271ME61G 330 F61 700 26 2,600 APXT4R0ARA331MF61G 4 390 F61 780 26 2,600 APXT4R0ARA391MF61G 680 F80 1,360 22 2,850 APXT4R0ARA681MF80G 150 E61 700 26 2,350 APXT6R3ARA151ME61G 220 E61 700 26 2,350 APXT6R3ARA221ME61G 6.3 220 F61 700 26 2,600 APXT6R3ARA221MF61G 330 F61 1,030 26 2,600 APXT6R3ARA331MF61G 560 F80 1,760 22 2,850 APXT6R3ARA561MF80G 120 E61 700 45 2,000 APXT100ARA121ME61G 10 220 F61 1,100 40 2,200 APXT100ARA221MF61G 390 F80 1,950 22 2,850 APXT100ARA391MF80G 100 E61 800 45 2,000 APXT160ARA101ME61G 16 180 F61 1,440 40 2,200 APXT160ARA181MF61G 270 F80 2,160 22 2,850 APXT160ARA271MF80G RATED RIPPLE CURRENT MULTIPLIERS Frequency Multipliers Frequency(Hz) 120 1k 10k 50k 100k to 500k SMD type 0.05 0.30 0.55 0.70 1.00 Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications. CAT. No. E1001U