SMH Series Snap Mount Large Capacitance High CV High Ripple RoHS Compliant 85 C Maximum Temperature The SMH series capacitors are the standard 85 C, large capacitance, snap-in capacitors from United Chemi-Con. The load life for the SMH series is 2,000 hours at 85 C with the rated ripple current applied. The very high CV values and ripple current capabilities make these capacitors ideal for use in power supply filter circuits. The SMH capacitors are available in 2 or 4-pin snap-in styles and 4 or 5-pin straight terminals. The SMH series is RoHS compliant offering Pb-free construction. The standard SMH series capacitors are not solvent proof. Refer to guidelines and precautions on the website for usage and installation conditions recommended for United Chemi-Con products. Summary of Specifications PC board 2 or 4-pin snap-in optional 4 or 5-pin straight terminals. Capacitance range: 56 to 270,000F. Voltage range: 6.3 to 450VDC. Category temperature range: 40 Cto 85 C for 6.3 to 100V 25 Cto 85 C for 160 to 450V. Leakage current: 0.02CV(A) or 3mA, whichever is smaller, after 5 minutes at 20 C. Standard capacitance tolerance: 20% Nominal case size (D L): 22 20mm to 40 80mm. Rated lifetime: 2,000 hours at 85 C with the rated ripple current applied. 18 United Chemi-Con, Inc. 9801 W. Higgins Road, Rosemont, IL 60018 Tel 847-696-2000 Fax 847-696-9278 www.chemi-con.com SMH SNAP MOUNT 85 CSMH SNAP MOUNT 85 C SMH Series SMH Specifications - Snap Mount Item Characteristics Category Temperature Range 40 to 85 C for 6.3 to 100VDC 25 to 85 C for 160 to 450VDC Rated Voltage Range 6.3 to 450VDC Capacitance Range 56 to 270,000 F Capacitance Tolerance 20% (M) at 20 C, 120Hz Leakage Current I 0.02CV ( A) or 3mA, whichever is smaller, after 5 minutes at 20 C. Where I = Max. leakage current ( A), C = Nominal capacitance ( F) and V= Rated voltage (V) Dissipation Factor (Tan )At 20 C, 120Hz Rated Voltage (V) 6.3 10 16 25 35 50 63-100 160-250 315-450 0.10 Tan (DF) Max. 0.60 0.50 0.40 0.30 0.25 0.20 0.15 * * 0.15 *0.15 maximum for 35mm and 40mm diameter. For rated voltages 63V, values are not valid for case sizes >35mm in diameter or >50mm in length. Low Temperature At 120Hz, impedance (Z) ratio between the 25 C or 40 C value and 20 C value shall not Characteristics exceed the values given below. Rated Voltage (V) 6.3-16 25 35 50, 63 80,100 160-400 450 Z( 25 C) /Z( 20 C) 4 3 3 2 2 4 8 Z( 40 C) /Z( 20 C) 15 10 8 6 5 Rated Ripple Current Multipliers Ambient Temperature ( C) 45 C 60 C 70 C 85 C 1.73 1.50 1.32 1.00 Frequency (Hz) DC Rated Voltage 50Hz 120Hz 300Hz 1kHz 10kHz 100kHz 6.3-50V 0.95 1.00 1.03 1.05 1.08 1.08 63-100V 0.92 1.00 1.07 1.13 1.19 1.20 160-250V 0.81 1.00 1.17 1.32 1.45 1.50 315-450V 0.77 1.00 1.16 1.30 1.41 1.43 Endurance The following specifications shall be satisfied when the capacitors are restored to 20 C after (Load Life) subjecting them to DC voltage for 2,000 hours at 85 C with the rated ripple current applied. The sum of the DC voltage and peak AC voltage must not exceed the full rated voltage of the capacitors. Capacitance change: 20% of initial measured value Tan (DF) : 200% of initial specified value Leakage current : initial specified value Shelf Life The following specifications shall be satisfied when the capacitors are restored to 20 C after exposing them for 1,000 hours at 85 C without voltage applied. The rated voltage shall be applied to the capacitors for a minimum of 30 minutes, at least 24 hours and not more than 48 hours before the measurements. Capacitance change: 20% of initial measured value Tan (DF) : 150% of initial specified value Leakage current : initial specified value United Chemi-Con, Inc. 9801 W. Higgins Road, Rosemont, IL 60018 Tel 847-696-2000 Fax 847-696-9278 www.chemi-con.com 19