KTS501B684M76N0T00 Chemi-Con

MULTILAYER CERAMIC CHIP CAPACITORS RoHS2 Compliant Series Series NTS / NTF (General product) Temperature cycle : 1000 cycles FEATURES 1. Large capacitance by small size. 2. X7R and X7S temperature characteristics. 3. High permissible ripple current capability. 4. NTF: Temperature cycle : 1000 cycles. APPLICATIONS 1. Smoothing circuit of DC-DC converters. 2. On-board power supplies. 3. Voltage regulators for computers. 3. Noise suppressor for various kinds of equipments. 4. High reliability equipments. CONSTRUCTION Ceramic Dielectric Termination (Tin Plating) Internal Electrode RATINGS 1. Category Temperature Range -55 to +125 2. Rated Voltage Range 25, 35, 50, 100, 250, 500Vdc 3. Rated Capacitance Range 0.010 to 47 F 4. Rated Capacitance Tolerance M (20%) : Standard, K (10%) 5. Temperature Characteristics X7R 6. Rated Ripple Current See No.5 on the following table SPECIFICATIONS No. Items Specification Test Condition 1 Withstand Voltage No abnormality. Rated voltage Withstand voltage Less than 250V 250% of rated voltage More than 250V 100V + Less than 500V 150% of rated voltage 130% of rated voltage More than 500V Shall be applied for 5 seconds. 2 Insulation Resistance 100/CR(M) or 4000(M) Rated voltage shall be applied for 605 seconds at temperature 252. whichever is less. 3 Rated Capacitance Within specified tolerance. CR 10F CR>10F Temperature 252 X7R temperature characteristics 4 Dissipation Factor Frequency 10.1kHz 12012Hz of 5.0 or less X7S temperature characteristics Voltage 10.2Vrms 0.50.2Vrms of 7.5 or less 10kHz1MHz (sine curve) 5 Rated Ripple Current See STANDARD RATINGS Ripple voltage Vp shall be less than the rated voltage. As customer requirement, Chemi-Con has submits the test results according to AEC-Q200 for Multilayer ceramic capacitors. Please contact us for more information. Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications. 13 CAT. No. E1002Z Ver.2MULTILAYER CERAMIC CHIP CAPACITORS NTS Series NTF Series / SPECIFICATIONS No. Items Specification Test Condition 6 Adhesion No visible damage. Substrate 5N (0.51kgf) for 101 seconds Capacitor 7 Bend strength of the face plating Appearance : No visible damage. The substrate shall be bend at a rate of 1mm/s C/C : 15% for 5 seconds. Press bar Press Capacitor Substrate Bending capability* 452mm 452mm Support *Bending capability NTS : 1mm NTF : 1mm or 2mm 8 Solderability Min. 75% of surface of the termination Solder Pb Free shall be covered with new solder Solder Temperature 2455 Dipping Time 20.5sec. 9 Resistance to Soldering Heat Appearance : No visible damage. Preheating Condition : C/C : 15% Step Temperature Time D.F. : To meet the initial specification. 1 10010 2min. I.R. : To meet the initial specification. 2 20010 2min. Solder Temperature : 2605 Dipping Time : 20.5 seconds 10 Temperature Cycle Appearance : No visible damage. Step Temperature () (min.) C/C : 15% 1 Min. Category temperature 3 303 D.F. : To meet the initial specification. 2 Room temperature 3 max. I.R. : To meet the initial specification. 3 Max. Category temperature 3 303 4 Room temperature 3 max. For above temperature cycle. NTS : For 5 cycles NTF : For 1000 cycles 11 Humidity Load Life Appearance : No abnormality. Temperature : 402 C/C : 15% Humidity : 90 to 95%RH I.R. : 25/CR(M) or 1000(M) Voltage : Rated voltage 24 whichever is less. Time : 500 hours 0 Dissipation Factor X7R temperature characteristics D.F: 10% or less X7S temperature characteristics D.F: 15% or less Temperature : 1253 12 Endurance Appearance : No abnormality. Voltage : Rated voltage C/C : 15% 48 I.R. : 50/CR(M) or 1000(M) Time : 1000 hours 0 whichever is less. Dissipation Factor X7R temperature characteristics D.F: 10% or less X7S temperature characteristics D.F: 15% or less *CR : Rated Capacitance( F) Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications. 14 CAT. No. E1002Z Ver.2