KVD250L105M32A0T00 Chemi-Con

DIPPED RADIAL LEAD MULTILAYER CERAMIC CAPACITORS High RoHS2RoHS AEC- temperature CompliantCompliant Q200 Series KVD 150 FEATURES 1. Temperature range : -55 to +150 2. Temperature characteristic : X8L 3. Small in size and wide capacitance range. Max. 15F is available. 4. Epoxy resin(UL94 V-0)used for coating. 5. Automotive grade(AEC-Q200) APPLICATIONS 1. Noise fillter for automotive equipment(ECU etc.) 2. Equipment used in a high temperature environment CONSTRUCTION Ceramic Dielectric Coating Resin Termination Solder (Pb-free) Internal Electrode Lead Wire RATINGS 1. Category Temperature Range -55+150 2. Rated Voltage Range 25, 50, 100 Vdc 3. Rated Capacitance Range 0.115F 4. Rated Capacitance Tolerance M(20%) 5. Temperature Characteristics X8L 6. Rated Ripple Current See No.5 on the following table SPECIFICATIONS No. Items Specification Test Condition 1 Withstand Between No abnormality. 250% of rated voltage shall be applied for 5 seconds. Voltage Terminals (Only 250Vdcdc products : 475V) products : 475V) Terminals to Coating Resin 2 Insulation Resistance 100/CR(M) or 4000(M) Rated voltage shall be applied for 605 seconds at whichever is less. temperature 252. 3 Rated Capacitance Within specified tolerance. CR 10F CR>10F Temperature 252 Frequency 10.1kHz 12012Hz 4 Dissipation Factor 5.0% maximum. Voltage 10.2Vrms 0.50.2Vrms As customer requirement, Chemi-Con has submits the test results according to AEC-Q200 for Multilayer ceramic capacitors. Please contact us for more information. Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications. 32 CAT. No. E1002ZDIPPED RADIAL LEAD MULTILAYER CERAMIC CAPACITORS KVDSeries SPECIFICATIONS No. Items Specification Test Condition 10kHz to 1MHz (sine curve) Ripple voltage Vp shall be less than the rated Size code 32 43 55 voltage. 5 Rated Ripple Current Arms 0.3 0.8 1.0 The surface temperature of MLCC must not exceed the maximum category temperature when the ripple current is applied. Appearance : No structural damage such as cracks Temperature Max. category temperature3 48 C/C : 20% Time 1000 hours 0 High Temperature 6 D.F. : 10% maximum Exposure(Storage) I.R. 50/CR(M) or 1000(M) whichever is less. Appearance : No visible damage. Step Temperature() (min) C/C : 15% 1 Min Category temperature 3 30 3 D.F. : To meet the initial specification. 2 Room temperature 3 max. 7 Temperature Cycle I.R. : To meet the initial specification. 3 Max. Category temperature 3 303 4 Room temperature 3 max. For 1000 cycles Appearance : No abnormality. Temperature 853 C/C : 20% Humidity 80 85%RH 8 Biased Humidity D.F. : 10% maximum Voltage Rated voltage 48 I.R. : 25/C (M) or 1000(M) R Time1000 hours 0 whichever is less. Appearance : No structural damage such as cracks Temperature Max. category temperature3 C/C : 20% Voltage Rated voltage 48 9 Operational Life D.F. : 10% maximum Time 1000 hours 0 I.R. : 50/C (M) or 1000(M) R whichever is less. The force applied shall be : Tension Lead (mm) Tensile(N) (sec.) Terminal 0.5 max. 5 10 1 10 Strength No visible damage. Lead (mm) Bending(N) (kg) (Leaded) 0.5 max. 2.5 0.25 Bending Time : 2times. Appearance : No abnormality. MIL-STD-202 Method 213 Condition C Peak value 100G C/C To meet the initial specification. Normal duration 6 ms D.F. : To meet the initial specification. 11 Mechanical Shock Velocity change 12.3 ft/sec(3.8m/s) Direction and time 3 times each in X,Y, Z axis. Total 18 times Appearance : No abnormality. MIL-STD-202 Method 204 Test condition 5G peak C/C To meet the initial specification. Amplitude 1.5mm max. D.F. : To meet the initial specification. 12 Vibration Frequency 10-2000-10Hz(20 minute) Direction and time 12 times each in X,Y, Z axis. Total 36 times Appearance : No visible damage. Solder temp. 260 5 Resistance to C/C : 15% Dipping Time 101s 13 Soldering Heat D.F. : To meet the initial specification. Depth : 1.5 to 2mm I.R. : To meet the initial specification. Appearance : No abnormality. AEC-Q200-002 C/C To meet the initial specification. Connection Between terminals 14 ESD Direct Contact 8kV(150pF 2000) D.F. : To meet the initial specification. Times 1time I.R. : To meet the initial specification. Min. 75% of surface of the termination Solder Pb Free shall be covered with new solder. Solder Temperature 245 5 15 Solderability Dipping Time 20.5s *CR : Rated Capacitance(F) Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications. 33 CAT. No. E1002Z