Acrylic UV+ Conformal Coating 1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION Product Name: ChemTools Acrylic Conformal Coat Product Type: Protective lacquer for industrial use. Company Address: ChemTools Pty. Ltd., PO Box 463, Emu Plains, NSW 2750 Ph: 02 4735 3126 EMERGENCY PHONE: Australia: Poisons Information Centre 13 1126 International: Infotrac (708) 918 1900 2. COMPOSITION/INFORMATION ON INGREDIENTS Hazardous components CAS % HSIS TWA HSIS STEL 3 3 Toluene 108-88-3 30 - 60 50ppm (191mg/m ) 150ppm (574mg/m ) 3 3 Acetone 67-64-1 30 - 60 500ppm (1185mg/m ) 1000ppm (2375mg/m ) 3. HAZARDS IDENTIFICATION Hazard Classification: Hazardous Substance, Dangerous Goods. F, Xi, Xn Risk Phrases: R11 Highly flammable R20/22 - Harmful by inhalation and if swallowed. R36/38 Irritating to eyes and skin. R65 Harmful: may cause lung damage if swallowed. R67 Vapours may cause drowsiness and dizziness. Safety Phrases: S2 Keep out of reach of children S7/9 Keep container tightly closed and in a well ventilated place S21 When using do not smoke S23 Do not breathe vapour. S51 Use only in well ventilated areas. S24/25 Avoid contact with skin and eyes. S36/37 Wear suitable protective clothing and gloves S62 - If swallowed, do not induce vomiting seek medical advice immediately and show this container or label. Overview: POISON DANGER HARMFUL OR FATAL IF SWALLOWED. HARMFUL IF INHALED OR ABSORBED THROUGH SKIN. VAPOR HARMFUL. FLAMMABLE LIQUID AND VAPOR. MAY AFFECT LIVER, KIDNEYS, BLOOD SYSTEM, OR CENTRAL NERVOUS SYSTEM. CAUSES IRRITATION TO SKIN, EYES AND RESPIRATORY TRACT. Relevant routes of exposure: Skin, Inhalation, Eyes Potential Health Effects Inhalation: May cause respiratory tract irritation. High concentrations of vapours may cause headache, fatigue, drowsiness And dizziness. Skin contact: May cause allergic skin reaction. May cause skin irritation. Product has a defatting effect on skin. Prolonged Contact may cause dryness of skin. Eye contact: Contact with eyes will cause irritation. 4. FIRST AID MEASURES Inhalation: Remove to fresh air. If symptoms develop and persist, get medical attention. Skin contact: Wash with soap and water. Remove contaminated clothing and shoes. Wash clothing before reuse. Get medical attention if symptoms occur. Eye contact: Check for and remove any contact lenses. Immediately flush with copious amounts of water, preferably, Lukewarm water for at least 15 minutes, holding eyelids open all the time. Get medical attention. Ingestion: Do not induce vomiting. Give large quantities of water Rinse mouth thoroughly. Loosen any tight clothing. Keep individual calm. Obtain medical attention. If there are signs of intoxication (drunkenness) then serious health effects may follow (depending on the amount swallowed or inhaled). Treat unconsciousness by placing the person in the coma position. Apply artificial respiration if breathing stops. Immediate medical attention should be sought and the affected person transferred and accompanied to the care of a doctor or hospital. Chemtools P/L Unit 4, 3 Pullman Place Emu Plains, NSW 2750 Phone: 02 4735 3126 Fax: 02 4735 3746 info chemtools.com.au www.chemtools.com.au Material Safety Data Sheet Acrylic UV+ Conformal Coating 5. FIRE-FIGHTING MEASURES Flash point: -20C (Closed Cup) Autoignition temperature: 422C (ASTM D-2155) Flammable/Explosive limits-lower %: 1.1% Flammable/Explosive limits-upper %: 7.1% Extinguishing media: Alcohol resistant foam, dry chemical or carbon dioxide. Special fire fighting procedures: Use water to cool exposed containers. Heating can cause expansion or decomposition leading to violent ruptures of containers. If safe to do so, remove containers from path of fire. Spills and leaks may be washed away with copious volumes of water, fog, or spray. For major fires or where the atmosphere is oxygen deficient or contains unacceptable levels of combustion products, fire-fighters must wear self contained breathing apparatus with full face mask and protective clothing. Unusual fire or explosion hazards: None Hazardous combustion products: Oxides of carbon. Keep run-off water out of sewers and water sources. Hazchem Code: 3 Y E 6. ACCIDENTAL RELEASE MEASURES Environmental precautions: Extinguish all ignition sources. Ventilate well. Use approved respirator if air contamination is Above accepted level. Prevent product from entering drains or open waters. Clean-up methods: Soak up with inert absorbent. Store in a partly filled, closed container until disposal. 7. HANDLING AND STORAGE Handling: Avoid contact with eyes, skin and clothing. Avoid breathing vapour and mist. Wash thoroughly after handling. Storage: For safe storage, store at or below 38C (100F). Keep in a cool, well ventilated area away from heat, sparks and open flame. Keep container tightly closed until ready for use. Incompatible products: Refer to Section 10. 8. EXPOSURE CONTROLS / PERSONAL PROTECTION Engineering controls: No specific ventilation requirements noted, but forced ventilation may still be required if concentrations Exceed occupational exposure limits. Respiratory protection: Use NIOSH approved respirator if there is potential to exceed exposure limit(s). Skin protection: Use impermeable gloves and protective clothing as necessary to prevent skin contact. Neoprene gloves. Butyl rubber gloves. Eye/face protection: Safety goggles or safety glasses with side shields. Eye wash facilities should be provided in all areas where the product is handled. See Section 2 for exposure limits. 9. PHYSICAL AND CHEMICAL PROPERTIES Physical state: Liquid. Colour: Clear, colourless. Odour: Organic, Aromatic. pH: Not available Boiling point/range: 56-110C. Melting point/range: -95C Specific gravity: 0.8 at 20C. Vapour density: 3.14 at 20C (air=1) Evaporation rate: 2.24 (ASTM D-3539, nBuAc=1) Solubility in water: Partially soluble. 10. STABILITY AND REACTIVITY Stability: Stable under normal conditions of use. Hazardous polymerization: Will not occur. Hazardous decomposition products: Oxides of carbon. Incompatibility: Strong oxidizers. Strong acids. Chlorine, Nitrogen tetraoxide Conditions to avoid: SeeHandling and Storag (Section 7) andIncompatibilit (Section 10). Chemtools P/L Unit 4, 3 Pullman Place Emu Plains, NSW 2750 11. TOXICOLOGICAL INFORMATION Phone: 02 4735 3126 Product toxicity data: Fax: 02 4735 3746 3 toluene Oral: LD 636 mg/Kg (rat). Skin: LD 14,100mg/Kg (rabbit) Inhalation LC :49g/m /4hr (rat) 50 50 50 Irritation Data: 500mg (skin rabbit), Moderate. 2mg/24hr (eye rabbit) Severe. info chemtools.com.au Has shown some evidence of reproductive effects in laboratory animals IARC Category 3 www.chemtools.com.au acetone Oral: LD 5800 mg/Kg (rat). Inhalation LC : 50,100mg/Kg (rat) 50 50 Material Safety Data Sheet