Tip Tinners 1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION Product Name: Chemtools Tip Tinners Product Type: Tinning and cleaning aid for soldering irons Part Numbers: CT-TC1 Company Address: ChemTools Pty. Ltd., PO Box 4319, Penrith, NSW 2750 Ph: 02 4735 3126 EMERGENCY PHONE: Australia: Poisons Information Centre 13 1126 International: Infotrac (708) 918 1900 2. COMPOSITION/INFORMATION ON INGREDIENTS Components CAS % HSIS TWA HSIS STEL 3 Tin 7440-31-5 <60 2mg/m N/A 2-hydroxypropane- 1,2,3-tricarboxylic acid 77-92-9 <30 Hydroxybutanedioic acid 6915-15-7 <30 alcohol ethoxylate 68439-46-3 <10 Non hazardous ingredients n/a <10 3. HAZARDS IDENTIFICATION Hazard Classification: Not classified as a Hazardous Substance according to the criteria of SafeWork Australia. Risk Phrases: Safety Phrases: S2 Keep out of reach of children Relevant routes of exposure: Ingestion. Potential Health Effects Inhalation: The fumes produced during use will irritate the nose and throat. Skin contact: Skin irritation may result from prolonged contact. Eye contact: Fumes produced during use may irritate the eyes. Ingestion: Will irritate the digestive tract. 4. FIRST AID MEASURES Inhalation: Remove the source of contamination or move the victim to fresh air. Ensure airways are clear. Administer oxygen if breathing is difficult. If symptoms develop and persist, seek medical attention Skin contact: Wash the affected area with plenty of cold or lukewarm running water. If symptoms develop and persist, seek medical attention. Eye contact: Flush immediately with copious amounts of water holding eyelid(s) open. Take care not to rinse contaminated water into the non-affected eye. If symptoms develop and persist seek medical attention. Ingestion: Do NOT induce vomiting. Wash out mouth with water. If symptoms develop and persist, seek medical attention 5. FIRE-FIGHTING MEASURES Flash point: >200C (Closed Cup) Autoignition temperature: Non Flammable Flammable/Explosive limits-lower %: N/A Flammable/Explosive limits-upper %: N/A Extinguishing media: N/A Special fire fighting procedures: N/A Unusual fire or explosion hazards: None Hazardous combustion products: Under fire conditions this product may emit toxic and/or irritating fumes including carbon monoxide, carbon dioxide, oxides of nitrogen, soot and organic substances Hazchem Code: N/A 6. ACCIDENTAL RELEASE MEASURES Environmental precautions: Dispose of waste according to federal, Environmental Protection Authority and state regulations. If large spillages of this material enters the waterways contact Material Safety Data Sheet Issued by: Chemtools Pty., Ltd., Page 1 of 3 info chemtools.com.au info chemtools.com.au www.chemtools.com.au www.chemtools.com.au Tip Tinners the Environmental Protection Authority, or your local Waste Management Authority. Clean-up methods: Use appropriate personal protective equipment during clean-up 7. HANDLING AND STORAGE Handling: No special handling procedures are required. Wash hands thoroughly after handling Storage: Store in a cool, dry well-ventilated area away from heat, oxidising agents and out of direct sunlight. Keep out of reach of children and away from foodstuffs. Incompatible products: Refer to Section 10. 8. EXPOSURE CONTROLS / PERSONAL PROTECTION Engineering controls: No exposure standards have been established for this material by HSIS. However, as with all chemicals, exposure should be kept to the lowest possible levels. Respiratory protection: Not normally required. However if engineering controls are not effective in controlling airborne exposure then respiratory protective equipment should be used suitable for protecting against fume. Reference should be made to Australian Standards AS/NZS 1715, Selection, Use and maintenance of Respiratory Protective Devices and AS/NZS 1716, Respiratory Protective Devices Skin protection: Gloves are recommended as good industrial practice Eye/face protection: Safety glasses are recommended as good industrial practice. See Section 2 for exposure limits. 9. PHYSICAL AND CHEMICAL PROPERTIES Physical state: Solid (tablet). Colour: Grey Odour: None. pH: N/A Boiling point/range: >500C. Melting point/range: >200C Specific gravity: Approx. 4 g/cm Vapour density: N/A Evaporation rate: N/A Solubility in water: Partially soluble. 10. STABILITY AND REACTIVITY Stability: Stable at normal temperatures and conditions. Hazardous polymerization: Will not occur. Hazardous decomposition products: In case of incomplete combustion and/or thermal decomposition carbon monoxide, carbon dioxide may be released. Molten tin may be formed. Incompatibility: Strong oxidising agents. Conditions to avoid: SeeHandling and Storag (Section 7) andIncompatibilit (Section 10). 11. TOXICOLOGICAL INFORMATION Product toxicity data: Not determined. 12. ECOLOGICAL INFORMATION Ecological information: The product is not readily biodegradable but inherently biodegradable. 13. DISPOSAL CONSIDERATIONS Recommended method of disposal: Recycle if possible. Dispose of according to Federal, State and local governmental regulations. 14. TRANSPORT INFORMATION Not classified as a Dangerous Good, according to the Australian Code for the Transport of Dangerous Goods by Road and Rail (6th Edition). Domestic (Land): Proper shipping name: No information found Material Safety Data Sheet Issued by: Chemtools Pty., Ltd., Page 2 of 3 info chemtools.com.au info chemtools.com.au www.chemtools.com.au www.chemtools.com.au