40-3-5 Chemtronics

CHEMTRONICS TDS SWPbFree Technical Data Sheet Soder-Wick Lead-Free SD Desoldering Braid TYPICAL PRODUCT DATA AND PRODUCT DESCRIPTION PHYSICAL PROPERTIES Soder-Wick Lead-Free is the state of the art in desoldering technology. It is specially designed for removal of todays high Flux Type High-Temperature No Clean temperature lead-free solders. The single Type ROL0 layer weave used for Soder-Wick Lead- Specifications: ANSI/IPC J STD-004 Free braid is lighter in mass than any other MIL-F-14256 F desoldering braid available and allows for lead-free solder removal at lower No Clean Flux Spec: MIL-STD-883B temperatures. Soder-Wick Lead-Free Bellcore TR-NWT-000078 responds faster than any other conventional ANSI/IPC J SF818 desoldering braid. This unique design Shelflife: 2 years minimizes overheating and requires less contact time thus preventing heat damage to the PCB and sensitive components. For Width Width Lead-Free rework, Soder-Wick has the Size Inches Color Metric answer. 2 .060 Yellow 1.5 mm Fastest wicking and heat transfer High capacity for solder uptake 3 .080 Green 2.0 mm Halide free, no corrosive residues 4 .110 Blue 2.8 mm Minimizes risk of heat damage to pads, components and PBCs STATIC DISSIPATIVE PACKAGING Can be used with Tin/Lead solders Soder-Wick Lead-Free is packaged on RoHS compliant Static Dissipative bobbins to minimize the TYPICAL APPLICATIONS risk of damage associated with static Soder-Wick Lead-Free desoldering braid electricity. The static dissipative bobbins qualify as electrostatic discharge protective safely removes solder from: Thru-hole Components per MIL-STD-1686C and MIL-HDBK- 263B and meet the static delay rate SMT Pads and BGA Pads Micro Circuits provision of MIL-B-81705C. Terminals, Lugs and Posts Identification Script USAGE INSTRUCTIONS AVAILABILITY 40 Series Lead-Free No Clean Flux For industrial use only. 25 bobbins / bag Read MSDS carefully prior to use. 1) Choose a Soder-Wick Lead-Free braid width Part Size equal to or slightly larger than the pad or connection. 5 feet 10 feet 2) Choose a solder iron tip equal to or slightly 40-2-5 40-2-10 2 larger than the pad or connection. 40-3-5 40-3-10 3 3) Set temperature of iron between 650 and 750F 40-4-5 40-4-10 4 4) Place wick on solder joint or pad and place tip of hot iron on top of wick 5) As solder becomes molten, the color of the wick Part Size VacuPak Packaging will change from copper to silver. The VacuPak Can contains ten 6) Remove wick and iron simultaneously once SW14025 2 five-foot bobbins in a vacuum color change has stopped. sealed can. This package 7) The component lead / pad is now clean and free SW14035 3 provides the highest level of from solder. cleanliness and freshness. Great 8) Clip and discard the used portion of the wick. SW14045 4 for tool kit storage. 9) If needed, clean PCB with CircuitWorks Lead- Free Flux Remover Pen CW9400 and remove soils with a ControlWipes absorbent wipe. NOTE: This information is believed to be accurate. It is intended for professional end users having the skills to evaluate and use the data properly. CHEMTRONICS SODER-WICK IS DESIGNED TO MEET does not guarantee the accuracy of the data and assumes OR EXCEED THE FOLLOWING: no liability in connection with damages incurred while MIL-F-14256F, Type R using it. NASA-STD-8739.3 DOD-STD-883E, Method 2022 Chemtronics ANSI/IPC J STD-004, Type ROL0 8125 Cobb Center Drive BELLCORE TR-NWT-000078 Kennesaw, GA 30152 ANSI/IPC J SF-818 1-770-424-4888 REV. A (02/05) SODER-WICK SD BOBBINS ARE Chemtronics, Soder-Wick and CircuitWorks are DESIGNED TO MEET OR EXCEED: registered trademarks of Chemtronics. All rights reserved. MIL-STD-2000A Vacu-Pak and ControlWipes are trademarks of MIL-B-81705C Chemtronics. All rights reserved. MIL-STD-1686C MIL-HDBK-263B TECHNICAL & APPLICATION DISTRIBUTED BY: ASSISTANCE Chemtronics provides a technical hotline to answer your technical and application related questions. The toll free number is: 1-800-TECH-401.