Conforms to Regulation (EC) No. 1907/2006 (REACH), Annex II - Europe SAFETY DATA SHEET Soder-Wick(R) No Clean Desoldering Braid 1. IDENTIFICATION OF THE SUBSTANCE/MIXTURE AND OF THE COMPANY/UNDERTAKING Identification of the substance or mixture Product name : Soder-Wick(R) No Clean Desoldering Braid Chemical name : No Clean flux coated, braided copper wire Synonyms : Soder-Wick(R) No Cleain, Soder-Wick No Clean(R) SD, Soder-Wick(R) No Clean BGA. Various codes based on size and length, including but not limited to: SW16015, SW16025, SW16035, SW16045, SW16055, 60-BGA-5, 60-1-10, 60-1- 5, 60-2-10, 60-2-5, 60-3-10, 60-3-5, 60-4-10, 60-4-5, 60-5-10, 60-5-5, 60-6-5 Product type : Solid. Use of the substance/mixture : Desoldering Company/undertaking identification Manufacturer : ITW Chemtronics 8125 Cobb Center Drive Kennesaw, GA 30152 Tel. 770-424-4888 or toll free 800-645-5244 Distributor : Importer : ITW Contamination Control BV Saffierlaan 5 VZ-2132 Hoofddorp The Netherlands Tel: +31 88 1307 400 FAX: +31 88 1307 499 e-mail address of person : askchemtronics chemtronics.com responsible for this SDS Emergency telephone number : Chemtrec - 1-800-424-9300 or collect 703-527-3887 (with hours of operation) 2. HAZARDS IDENTIFICATION The product is classified as dangerous according to Directive 1999/45/EC and its amendments. Classification : R42/43 Physical/chemical hazards : FUMES MAY BE HARMFUL May be harmful by inhalation after often repeated exposure.Slightly hazardous by the following route of exposure:Skin contact irritant Human health hazards : Caution: exposure to this material may cause certain sensitive individuals to develop eczema and/or asthma. May cause sensitisation by inhalation and skin contact. Sensitised persons may subsequently show asthmatic symptoms when exposed to atmospheric concentrations well below the OEL. Additional hazards : May cause allergic reactions in certain individuals. See Section 11 for more detailed information on health effects and symptoms. 3. COMPOSITION/INFORMATION ON INGREDIENTS Substance/preparation : Mixture Ingredient name CAS % EC number Classification number 1 2 copper 7440-50-8 90 - 99 231-159-6 N R50 1 rosin 73138-82-6 1 - 3 277-299-1 R43 See Section 16 for the full text of the R-phrases declared above. There are no additional ingredients present which, within the current knowledge of the supplier and in the concentrations applicable, are classified as hazardous to health or the environment and hence require reporting in this section. 1 Substance classified with a health or environmental hazard 2 Substance with a workplace exposure limit Occupational exposure limits, if available, are listed in Section 8. 4. FIRST AID MEASURES First-aid measures Date of issue/Date of : 7/5/2011. 1/7 revisionSoder-Wick(R) No Clean Desoldering Braid 4. FIRST AID MEASURES Inhalation : Remove victim to fresh air and keep at rest in a position comfortable for breathing. If not breathing, if breathing is irregular or if respiratory arrest occurs, provide artificial respiration or oxygen by trained personnel. It may be dangerous to the person providing aid to give mouth-to-mouth resuscitation. Get medical attention if adverse health effects persist or are severe. If unconscious, place in recovery position and get medical attention immediately. Maintain an open airway. Loosen tight clothing such as a collar, tie, belt or waistband. Ingestion : Wash out mouth with water. Remove dentures if any. Remove victim to fresh air and keep at rest in a position comfortable for breathing. If material has been swallowed and the exposed person is conscious, give small quantities of water to drink. Stop if the exposed person feels sick as vomiting may be dangerous. Do not induce vomiting unless directed to do so by medical personnel. If vomiting occurs, the head should be kept low so that vomit does not enter the lungs. Get medical attention if adverse health effects persist or are severe. Never give anything by mouth to an unconscious person. If unconscious, place in recovery position and get medical attention immediately. Maintain an open airway. Loosen tight clothing such as a collar, tie, belt or waistband. Skin contact : Flush contaminated skin with plenty of water. Remove contaminated clothing and shoes. Wash contaminated clothing thoroughly with water before removing it, or wear gloves. Continue to rinse for at least 10 minutes. Get medical attention. In the event of any complaints or symptoms, avoid further exposure. Wash clothing before reuse. Clean shoes thoroughly before reuse. Eye contact : Immediately flush eyes with plenty of water, occasionally lifting the upper and lower eyelids. Check for and remove any contact lenses. Continue to rinse for at least 10 minutes. Get medical attention if irritation occurs. Protection of first-aiders : No action shall be taken involving any personal risk or without suitable training. It may be dangerous to the person providing aid to give mouth-to-mouth resuscitation. Wash contaminated clothing thoroughly with water before removing it, or wear gloves. Notes to physician : Treat symptomatically. Contact poison treatment specialist immediately if large quantities have been ingested or inhaled. See Section 11 for more detailed information on health effects and symptoms. 5. FIRE-FIGHTING MEASURES Extinguishing media Suitable : Use an extinguishing agent suitable for the surrounding fire. Not suitable : None known. Special exposure hazards : No specific fire or explosion hazard. Promptly isolate the scene by removing all persons from the vicinity of the incident if there is a fire. No action shall be taken involving any personal risk or without suitable training. This material is very toxic to aquatic organisms. Fire water contaminated with this material must be contained and prevented from being discharged to any waterway, sewer or drain. Hazardous thermal : Decomposition products may include the following materials: decomposition products metal oxide/oxides Special protective : Fire-fighters should wear appropriate protective equipment and self-contained breathing equipment for fire-fighters apparatus (SCBA) with a full face-piece operated in positive pressure mode. Clothing for fire-fighters (including helmets, protective boots and gloves) conforming to European standard EN 469 will provide a basic level of protection for chemical incidents. 6. ACCIDENTAL RELEASE MEASURES Personal precautions : No action shall be taken involving any personal risk or without suitable training. Evacuate surrounding areas. Keep unnecessary and unprotected personnel from entering. Do not touch or walk through spilt material. Provide adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Put on appropriate personal protective equipment (see Section 8). Environmental precautions : Avoid dispersal of spilt material and runoff and contact with soil, waterways, drains and sewers. Inform the relevant authorities if the product has caused environmental pollution (sewers, waterways, soil or air). Water polluting material. May be harmful to the environment if released in large quantities. Methods for cleaning up Small spill : Move containers from spill area. Vacuum or sweep up material and place in a designated, labelled waste container. Dispose of via a licensed waste disposal contractor. Large spill : Move containers from spill area. Approach the release from upwind. Prevent entry into sewers, water courses, basements or confined areas. Vacuum or sweep up material and place in a designated, labelled waste container. Dispose of via a licensed waste disposal contractor. Date of issue/Date of : 7/5/2011. 2/7 revision