CHEMTRONICS TDS SWPbFree Technical Data Sheet Soder-Wick Lead-Free SD Desoldering Braid TYPICAL PRODUCT DATA AND PRODUCT DESCRIPTION PHYSICAL PROPERTIES Soder-Wick Lead-Free is the state of the art in desoldering technology. It is specially Flux Type High-Temperature No Clean designed for removal of todays high temperature lead-free solders. The single Type ROL0 layer weave used for Soder-Wick Lead- Specifications: ANSI/IPC J STD-004 Free braid is lighter in mass than any other MIL-F-14256 F desoldering braid available and allows for lead-free solder removal at lower No Clean Flux Spec: MIL-STD-883B temperatures. Soder-Wick Lead-Free Bellcore TR-NWT-000078 responds faster than any other conventional ANSI/IPC J SF818 desoldering braid. This unique design Shelflife: 2 years minimizes overheating and requires less RoHS/WEEE contact time thus preventing heat damage to the PCB and sensitive components. For Status Lead-Free rework, Soder-Wick has the answer. Width Width Fastest wicking and heat transfer Size Inches Color Metric High capacity for solder uptake 2 .060 Yellow 1.5 mm Halide free, no corrosive residues 3 .080 Green 2.0 mm Minimizes risk of heat damage to pads, 4 .110 Blue 2.8 mm components and PBCs Can be used with Tin/Lead solders RoHS compliant STATIC DISSIPATIVE PACKAGING Soder-Wick Lead-Free is packaged on TYPICAL APPLICATIONS Static Dissipative bobbins to minimize the Soder-Wick Lead-Free desoldering braid risk of damage associated with static safely removes solder from: electricity. The static dissipative bobbins Thru-hole Components qualify as electrostatic discharge protective SMT Pads and BGA Pads per MIL-STD-1686C and MIL-HDBK- Micro Circuits 263B and meet the static delay rate Terminals, Lugs and Posts provision of MIL-B-81705C. Identification Script USAGE INSTRUCTIONS AVAILABILITY 40 Series Lead-Free No Clean Flux For industrial use only. 25 bobbins / bag Read MSDS carefully prior to use. 1) Choose a Soder-Wick Lead-Free braid width Part Size equal to or slightly larger than the pad or connection. 5 feet 10 feet 2) Choose a solder iron tip equal to or slightly 40-2-5 40-2-10 2 larger than the pad or connection. 40-3-5 40-3-10 3 3) Set temperature of iron between 650 and 750F 40-4-5 40-4-10 4 4) Place wick on solder joint or pad and place tip of hot iron on top of wick 5) As solder becomes molten, the color of the wick Part Size VacuPak Packaging will change from copper to silver. The VacuPak Can contains ten 6) Remove wick and iron simultaneously once SW14025 2 five-foot bobbins in a vacuum color change has stopped. sealed can. This package 7) The component lead / pad is now clean and free SW14035 3 provides the highest level of from solder. cleanliness and freshness. Great 8) Clip and discard the used portion of the wick. SW14045 4 for tool kit storage. 9) If needed, clean PCB with CircuitWorks Lead- Free Flux Remover Pen CW9400 and remove soils with a ControlWipes absorbent wipe. NOTE: This information is believed to be accurate. It is intended for professional end users having the skills to evaluate and use the data properly. ITW SODER-WICK IS DESIGNED TO MEET CHEMTRONICS does not guarantee the accuracy of OR EXCEED THE FOLLOWING: the data and assumes no liability in connection with MIL-F-14256F, Type R damages incurred while using it. NASA-STD-8739.3 DOD-STD-883E, Method 2022 MANUFACTURED BY: ANSI/IPC J STD-004, Type ROL0 ITW Chemtronics BELLCORE TR-NWT-000078 ANSI/IPC J SF-818 8125 Cobb Center Drive Kennesaw, GA 30152 SODER-WICK SD BOBBINS ARE 1-770-424-4888 REV. B (06/06) DESIGNED TO MEET OR EXCEED: MIL-STD-2000A Chemtronics , Soder-Wick and CircuitWorks are registered trademarks of ITW Chemtronics. All rights MIL-B-81705C reserved. Vacu-Pak and ControlWipes are trademarks of MIL-STD-1686C ITW Chemtronics. All rights reserved. MIL-HDBK-263B TECHNICAL & APPLICATION DISTRIBUTED BY: ASSISTANCE Chemtronics provides a technical hotline to answer your technical and application related questions. The toll free number is: 1-800-TECH-401.