SW60-4-10 Chemtronics

CHEMTRONICS TDS SWNoClean Technical Data Sheet Soder-Wick No Clean Desoldering Braid PRODUCT DESCRIPTION TYPICAL PRODUCT DATA AND PHYSICAL PROPERTIES Soder-Wick No Clean is designed to provide fast and safe desoldering without Surface Insulation Resistance leaving behind harmful flux residues. Soder- Bellcore TR-NWT-000078 : PASS Wick No Clean uses pure, oxygen free 4 After 96 Hours (megohms) 2 x 10 Limit copper braid and a patented flux technology to make an efficient and effective Group A Group B Group C 6 6 6 4.8 x 10 3.8 x 10 4.1 x 10 desoldering braid. Soder-Wick No Clean SD is available on ESD safe bobbins for : PASS ANSI/IPC J SF-818 8 After 168 Hours (ohms) 1.8 x 10 Limit protection against damage due to static 1-2 2-3 3-4 4-5 electricity. Requires little or no post solder cleaning 10 10 10 10 2.3 x 10 2.6 x 10 2.8 x 10 2.8 x 10 No corrosive residues Electromigration : PASS Halide free Average Insulation Resistance ESD Safe bobbins meet specs: (megohms)-One Decade Limit MIL-STD-1686C Initial Final 3 4 MIL-HDBK-263B Group E 3.93 x 10 1.24 x 10 3 4 Group F 3.87 x 10 2.84 x 10 Static decay provision of At 10x magnification no evidence of MIL-B-81705C electromigration or heavy corrosion. Minimal risk of heat and static component damage Silver Chromate Test Paper PASS Copper Mirror Test PASS TYPICAL APPLICATIONS Shelflife 2 years Soder-Wick No Clean safely removes RoHS/WEEE solder from: Status Lugs and Posts Micro Circuits Surface Mount Device Pads SODER-WICK NO CLEAN MEETS OR Ball Grid Array Pads EXCEEDS: MIL-F-14256F, Type R DOD-STD-883E, Method 2022 Bellcore TR-NWT-000078 ANSI/IPC J SF-818 AVAILABILITY Part Size Inches Color Size Metric Part Size Length Part Size Length 60-1-5 1 5 60-1-10 1 10 1 .030 White .76mm 60-2-5 2 5 60-2-10 2 10 2 .060 Yellow 1.52mm 60-3-5 3 5 60-3-10 3 10 3 .080 Green 2.03mm 60-4-5 4 5 60-4-10 4 10 4 .110 Blue 2.79mm 60-5-5 5 5 60-5-10 5 10 5 .145 Brown 3.68mm 60-6-5 6 5 6 .210 Red 5.33mm BGA - Purple - Part Size VacuPak Packaging The VacuPak Can contains SW16015 1 USAGE INSTRUCTIONS ten five-foot bobbins in a SW16025 2 For industrial use only. vacuum sealed can. This SW16035 3 Read MSDS carefully prior to use. package provides the highest SW16045 4 level of cleanliness and 1) Choose a Soder-Wick No Clean width equal to SW16055 5 freshness. Great for tool kit or slightly larger than the pad or connection. SW160BGA BGA storage. 2) Choose a solder iron tip equal to or slightly larger than the pad or connection. 3) Set temperature of iron between 600-750F. NOTE: 4) Place wick on solder joint and place tip of hot This information is believed to be accurate. It is iron on top of wick. intended for professional end users having the skills 5) As solder becomes molten, the color of the wick to evaluate and use the data properly. ITW will change from copper to silver. Chemtronics does not guarantee the accuracy of 6) Remove wick and iron from joint the data and assumes no liability in connection with simultaneously once color change has stopped. damages incurred while using it. 7) The component lead / pad is now clean and free from solder. 8) Clip and discard used portion of the wick. MANUFACTURED BY: ITW CHEMTRONICS TECHNICAL & APPLICATION 8125 COBB CENTER DRIVE ASSISTANCE KENNESAW, GA 30152 Chemtronics provides a technical hotline to 1-770-424-4888 REV. F (06/06) answer your technical and application related questions. The toll free number is: DISTRIBUTED BY: 1-800-TECH-401. Chemtronics , Soder-Wick and CircuitWorks are registered trademarks of ITW Chemtronics. All rights reserved. VacuPak is a trademark of ITW Chemtronics. All rights reserved.