V26 EC4AW SERIES 3.3-6 WATT 4:1 INPUT RANGE DC-DC CONVERTERS FEATURES * 3.3-6W Isolated Output * DIP-24/SMD Package * Efficiency to 83% * 4:1 Input Range * Regulated Outputs * Pi Input Filter * Continuous Short Circuit Protection * Without Tantalum Capacitor Inside * Safety Meets IEC/EN/UL 62368-1 MODEL INPUT OUTPUT OUTPUT INPUT CURRENT % EFF. CAPACITOR (1) (2) NUMBER VOLTAGE VOLTAGE CURRENT LOAD MAX. NO LOAD FULL LOAD (3) (4) EC4AW01 9-36 VDC 5 VDC 1000 mA 5 mA 254 mA 84 82 1000uF EC4AW02 9-36 VDC 12 VDC 470 mA 5 mA 283 mA 85 83 470uF EC4AW03 9-36 VDC 15 VDC 400 mA 5 mA 301 mA 85 83 400uF EC4AW04 9-36 VDC 12 VDC 230 mA 7.5 mA 280 mA 85 82 230uF EC4AW05 9-36 VDC 15 VDC 190 mA 7.5 mA 293 mA 85 81 190uF EC4AW06 9-36 VDC 5 VDC 500 mA 5 mA 251 mA 85 83 500uF EC4AW07 9-36 VDC 3.3 VDC 1000 mA 5 mA 176 mA 80 78 1000uF EC4AW11 18-72 VDC 5 VDC 1000 mA 5 mA 132 mA 83 79 1000uF EC4AW12 18-72 VDC 12 VDC 470 mA 5 mA 143 mA 86 82 470uF EC4AW13 18-72 VDC 15 VDC 400 mA 5 mA 154 mA 86 81 400uF EC4AW14 18-72 VDC 12 VDC 230 mA 7.5 mA 143 mA 85 80 230uF EC4AW15 18-72 VDC 15 VDC 190 mA 7.5 mA 148 mA 85 80 190uF EC4AW16 18-72 VDC 5 VDC 500 mA 5 mA 130 mA 84 80 500uF EC4AW17 18-72 VDC 3.3 VDC 1000 mA 5 mA 93 mA 79 74 1000uF NOTE: 1. Can be None, H, HM or HMS. 2. Nominal Input Voltage: 24 or 48 VDC. 3. Measured at 12VDC for 24Vin, 24VDC for 48Vin. 4. Measured at Nominal Input Voltage. 1 V26 SPECIFICATIONS All Specifications Typical at Nominal Line, Full Load, and 25 Unless Otherwise Noted INPUT SPECIFICATIONS: ISOLATION VOLTAGE: Input Voltage Range ........................ 24V ...................... 9-36V 1.5K VDC min. Standard or Suffix HM Models 48V ....................... 18-72V 3K VDC min. (note4) Suffix H Models Input Filter ....... Pi Type CASE MATERIAL: Standard Models . Non-Conductive Black Plastic OUTPUT SPECIFICATIONS: Voltage Accuracy .......................................................................... 2.0% max. Suffix HM Models (note5) .. Black Coated Copper with Non-Conductive Base Voltage Balance (Dual) .................................................................. 1.0% max. NOTE: Temperature Coefficient 0.05%/ max. 1. Measured from high line to low line. Ripple & Noise, 20MHz BW ..... 100mV pk-pk max. 2. Measured from full load to 10% load. Short Circuit Protection Continuous 3. Measured from full load to 1/4 load. Line Regulation Single/Dual (note1) ..........0.5% max. 4. Non-conductive black plastic only. Load Regulation Single (note2) .............. 0.5% max. 5. Suffix S to the model number with SMD packages. Dual (note3) .....1.0% max. 6. Maximum case temperature under any operating condition should Start up time . 30 ms typ. not be exceeded 100 GENERAL SPECIFICATIONS: Typical Derating curve for Natural Convection Efficiency .......................................................................................... See Table 120% 9 Isolation Resistance ............................................................ 10 Ohm min. -40 71 Switching Frequency .............................................................. 200KHz min. 100% Operating Ambient Temperature Range .................................. -40 to +85 De-rating, Above 71 ... Linearly to Zero Power at 100 80% Case Temperature..................................... 100 max Cooling .. Natural Convection 60% Storage Temperature Range ................. -40 to +100 Natural Dimensions DIP ..... 1.25x0.80x0.40 inches (31.8x20.3x10.2 mm) 40% Convection SMD ... 1.25x0.80x0.45 inches (31.8x20.3x11.4 mm) Weight ... 12.5g 20% 100 0% -40 -20 0 20 40 60 80 100 o Ambient Temperature( C) Case A Dimensions: CASE AS PIN CONNECTION Single Output Dual Output BOTTOM VIEW TOP VIEW Pin DIP DIP SMD SMD SEE NOTE 24 23 22 21 20 16 15 14 13 1,24 NP NC NP NC 24 1 -V Input 2,3 -V Input 23 2 22 3 4,5 NP NC NP NC 9 NC Common 1 2 3 4 5 9 10 11 12 10,15 NC NC 0.02 0.04 16 9 0.5 1.0 11 NC -V Output 15 10 14 11 12,13 NP NC NP NC 12 13 +V Output 14 +V Output 0.15 0.600 3.8 15.24 16 Common -V Output 0.40 0.80 0.08 0.100 20,21 NP NC NP NC 10.2 20.3 2.0 2.54 22,23 +V Input +V Input 1.25 NOTE:Pin Size is 0.020.002 Inch (0.50.05 mm) DIA 31.8 All Dimensions In Inches (mm) * NC-NO CONNECTION WITH PIN Tolerances Inches: X.XX= 0.02 , X.XXX= 0.010 * NP-NO PIN Millimeters: X.X= 0.5 , X.XX=0.25 2 1.25 31.8 0.100 0.08 2.54 2.0 1.00 25.4 0.80 20.3 LOAD(%) 0.43 10.9 0.45 11.4