F E D C B A AT ALL TIMES WATER RESISTANT n0,6 0,05 (9x) ( 5 : 1 ) CONNECTORS NOT IN USE SHOULD BE COVERED WITH A CONEC WATER RESISTANT CAP OR WATER TIGHT HOOD. SEALING D D COMPOUND 0,3 + 30,88 - 0,15 b +0,12 25 - 0,13 +0,23 16,81 - 0,02 POS. 1 POS. 6 SEALING GASKET +0,25 8,23 - 0 b RUBBER GASKET PLACED ON TOP SURFACE OF MALE INSULATOR C C 15-00644o CONEC ABC 4-40 UNC SEE NOTE 14 SW4,8 4-40 UNC c NOTES: B B 1. FOR WAVESOLDERING (SOLDER BATH TEMPERATURE 265C FOR 8 SEC. AND SOLDER PREHEAT 150C FOR 180 SEC.) 2. IP RATING: IP 67 3. SEALED TO WITHSTAND PRESSURE UP TO 1,45 PSI FOR 30 MINUTES AFTER SOLDERING 4. METALSHELL: ZINC DIE CAST min. 50in NICKEL PLATING over COPPER 5. INSULATORS: PBT GF UL 94 V-0 BLACK 6. SEALING GASKET: SILICONE BLUE 7. RUBBER GASKET: TPE BLACK 8. SEALING COMPOUND: EPOXY RESIN UL 94 V-0 BLACK 9. CONTACTS: COPPER ALLOY PLATING (SEE PART-NO.): o PLEASE ADD 1 for 30in HARD GOLD over min. 50in NICKEL o PLEASE ADD 3 for GOLD FLASH over NICKEL 10. REAR SPACER CLIPS: COPPER ALLOY min. 200in TIN over 80in NICKEL PCB-HOLE: n3,1 0,1mm PCB THICKNESS 1,6mm 11. HEXLOCKING SCREWS: STAINLESS STEEL 12. P.C.B. HOLE DRILLINGS and RECOMMENDED PANEL CUT-OUT ON SHEET 2 13. RECOMMENDED TORQUE FOR MOUNTING SCREW 35Ncm (3.1 in.LB) / max. 67Ncm (6 in.LB) 14. CONNECTOR IS PART MARKED: 15-00644o CONEC ABC (see note 9) scale: 2:1 (5:1) tolerance material: SEE NOTES dim. in mm A A date name title: drawn 10.09.14 Lehmenkhler D-SUB MALE appd. 26.01.15 Fischer 9pos. SOLDER PIN STRAIGHT norm with closed 4-40 UNC thread and rear spacer clip dwg no: 1 x c 5827 25.09.15 Unkrer d-old DIN- 2 x b 5800 04.09.15 M. H. A3 R 15K1A1545 a Original sh: 1 RoHS compliant rev. description date name part no: 15-00644o (see note 9) F E D C B A 10 +0,3 12,8 - 0,15 4,6 9,4 THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH 0,4 + 8,95 - 0,3 DO NOT ALTER CAD DRAWING BY HAND +0,4 11,85 - 0,3 +0,4 11,55 - 0,3 +0,25 2,55 - 0 0,12 + 5,64 - 0,18 0,13 R3,4 F E D C B A P.C.B. HOLE DRILLINGS ( P.C.B. TOP SIDE ) D D 0,12 + 25 - 0,13 5,49 0,1 n3,1 0,1 (2x) 2,74 0,1 1 +0,1 n1 (9x) - 0 0,1 1,37 4,11 0,1 C C RECOMMENDED PANEL CUT-OUT 0,1 20,5 i 0,26 A B B B 0,26 i B 0,1 25 A scale: 5:1 tolerance material: SEE SHEET 1 dim. in mm A A date name title: drawn 10.09.14 Lehmenkhler P.C.B. HOLE DRILLINGS appd. 26.01.15 Fischer RECOMMENDED PANEL CUT-OUT norm D-SUB MALE 9pos. SOLDER PIN STRAIGHT dwg no: d-old DIN- A3 R 15K1A1545 a Original sh: 2 rev. description date name part no: SEE SHEET 1 F E D C B A 1 1 0 0,05 (2x) n3,1 THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH DO NOT ALTER CAD DRAWING BY HAND 1,42 0,1 11,4 0,1 0,1 2,84