FFFF EEEE DDDD CCCC BBBB AAAA NOTES: 1. RECOMMENDED SOLDER INSTRUCTION SEE SHEET 2 n1,12 (50x) 2. METALSHELLS: COPPER ALLOY min. 320in TIN over 40-80in NICKEL ( 5 : 1 ) 3. INSULATORS: PBT GF UL 94 V-0 BLACK 4. CONTACTS: COPPER ALLOY SEALING PLATING: FLASH GOLD over NICKEL COMPOUND SOLDER CUP ACCEPTS CABLE AWG 20 DDDD DDDD 5. THREADED INSERTS: COPPER ALLOY min 200in TIN over 80in NICKEL 6. COLLARS: COPPER ALLOY min 200in TIN over 80in NICKEL 7. HEXLOCKING SCREWS: STAINLESS STEEL 8. FRAME: ZINC DIE CAST NICKEL PLATED 9. O-RING: SILICON BLUE 10. RUBBER GASKET: TPE BLACK 11. SEALING COMPOUND: PUR BLUE 12. RECOMMENDED PANEL CUT-OUT ON SHEET 2 13. RECOMMENDED TORQUE FOR MOUNTING SCREW 35Ncm (3.1 in.LB)/ max.40Ncm (3.5 in.LB) 14. CONNECTOR IS PART MARKED: 6STD50PAM99B30X CONEC ABC RUBBER GASKET 0,13 + 11,07 PLACED ON TOP SURFACE - 0,12 OF MALE INSULATOR AT ALL TIMES WATER RESISTANT CONNECTORS NOT IN USE SHOULD BE COVERED WITH A CONEC WATER RESISTANT CAP OR WATER TIGHT HOOD. CC CC CC CC +0,3 75,6 - 0 +0,12 1 61,1 - 0,13 18 0,12 + 52,81 34 - 0,13 BBBB BBBB 6STD50PAM99B30X CONEC ABC O-RING SEE NOTE 8 4-40 UNC SEE NOTE 14 SW 4,8 4-40 UNC scale: 2:1 (5:1) tolerance material: SEE NOTES dim. in mm AAAA AAAA date name title: drawn 20.03.12 Henneboel D-SUB MALE appd. 21.03.12 Fischer 50pos. SOLDER CUP norm with threaded insert and hexlocking screw dwg no: d-old DIN- A3 RR RR 15K1A1014 a Original sh: 1 Directive 2002/95/EC RoHS compliant rev. description date name part no: 6STD50PAM99B30X FFFF EEEE DDDD CCCC BBBB AAAA 10 0,3 + 23,9 - 0 9,4 4,6 THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH DO NOT ALTER CAD DRAWING BY HAND +0,25 3,6 - 0 +0 5,7 0,3 - 0,31 7,1FFFF EEEE DDDD CCCC BBBB AAAA DDDD DDDD Solder Instruction 1. Cable should be prepared for soldering. The cable/wires must be pretinned. 2. Insert cable/wire into solder cup. 3. Operate the soldering iron at 350C, 50 Watt max. and use a pencil tip. 4. Put tip to wire in solder cup. 5. After 1 second bring in solder. 6. Heat for 3 seconds longer. Do not heat contact more than 4 seconds in total. 7. Remove soldering iron. 8. Wait until solder gets rigid again. 9. Do not solder adjacent contacts consecutively, alternate position within the connector to minimize heat build up. CC CC CC CC RECOMMENDED PANEL CUT-OUT 56,3 0,1 i 0,26 A B BBBB BBBB i 0,26 B 0,1 61,1 A scale: 3:1 tolerance material: SEE SHEET 1 dim. in mm AAAA AAAA date name title: drawn 20.03.12 Henneboel RECOMMENDED PANEL CUT-OUT appd. 21.03.12 Fischer D-SUB MALE 50pos. SOLDER CUP norm with threaded insert and hexlocking screw dwg no: d-old DIN- A3 RR RR 15K1A1014 a Original sh: 2 rev. description date name part no: SEE SHEET 1 FFFF EEEE DDDD CCCC BBBB AAAA 10 R3,4 0,13 n3,1 0,05 (2x) THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH DO NOT ALTER CAD DRAWING BY HAND 0,1 14,1