Ordering information
AC-DC Power Supplies Enclosed Type
PL A 15 F -O -O
PLA15F
1 2 3 4 5 6
1 Series name
Example recommended EMI/EMC filter
R
2 Single output
NAC-04-472
3 Output wattage
4 Universal input
5 Output voltage
6 Optional *7
C : with Coating
J : Connector interface
T : Vertical terminal block
High voltage pulse noise type : NAP series
-NO : with DIN rail
Low leakage current type : NAM series
* A higher current rating EMI/EMC filter
may be recommended in view of the See 5.1 in Instruction Manual.
other devices that could be connected
in parallel with the power supply.
*Make sure necessary tests will be carried out on your end equipment with the power supply installed in accordance with any required EMC/EMI regulations.
SPECIFICATIONS
MODEL PLA15F-5 PLA15F-12 PLA15F-15 PLA15F-24
AC85 - 264 1f (Output derating is required at AC85V - 115V. See 1.1 and 3.2 in Instruction Manual) *3
VOLTAGE[V]
ACIN 100V 0.4typ (Io=90%)
CURRENT[A] ACIN 115V 0.4typ (Io=100%)
ACIN 230V 0.25typ (Io=100%)
FREQUENCY[Hz] 50 / 60 (47 - 63)
ACIN 100V 72.5typ (Io=90%) 75.5typ (Io=90%) 77.0typ (Io=90%) 78.0typ (Io=90%)
INPUT
EFFICIENCY[%] ACIN 115V 73.5typ (Io=100%) 77.0typ (Io=100%) 78.5typ (Io=100%) 79.0typ (Io=100%)
ACIN 230V 75.5typ (Io=100%) 78.5typ (Io=100%) 79.5typ (Io=100%) 80.0typ (Io=100%)
ACIN 100V 16typ (Io=90%) Ta=25C at cold start
INRUSH CURRENT[A] ACIN 115V 16typ (Io=100%) Ta=25C at cold start
ACIN 230V 32typ (Io=100%) Ta=25C at cold start
LEAKAGE CURRENT[mA] 0.30max (ACIN 115V / 240V, 60Hz, Io=100%, According to IEC60950-1 and DEN-AN)
VOLTAGE[V] 5 12 15 24
3 1.3 1 0.7
CURRENT[A]
ACIN 85-115V Output derating is required at ACIN 115V or less (refer to instruction manual 3.2)
WATTAGE[W]
ACIN 115V-264V 15.0 15.6 15.0 16.8
*4
LINE REGULATION[mV] 20max 48max 60max 96max
*4
LOAD REGULATION[mV] 40max 100max 120max 150max
0 to +50C 80max 120max 120max 120max
RIPPLE[mVp-p] *1 -10 to 0C 140max 160max 160max 160max
Io=0 to 35% 160max 240max 240max 280max
OUTPUT 0 to +50C 120max 150max 150max 150max
RIPPLE NOISE[mVp-p] *1 -10 to 0C 160max 180max 180max 180max
Io=0 to 35% 240max 300max 300max 320max
0 to +50C 50max 120max 150max 240max
TEMPERATURE REGULATION[mV]
-10 to +50C 60max 150max 180max 290max
DRIFT[mV] *2 20max 48max 60max 96max
START-UP TIME[ms] 200typ (ACIN 115V, Io=100%) *Start-up time is 700 ms typ for less than 1 minute of applying input again from turning off the input voltage.
HOLD-UP TIME[ms] 20typ (ACIN 115V, Io=100%)
OUTPUT VOLTAGE ADJUSTMENT RANGE[V] 4.50 to 5.50 10.80 to 13.20 13.50 to 16.50 21.60 to 26.40
OUTPUT VOLTAGE SETTING[V] 5.00 to 5.15 12.00 to 12.48 15.00 to 15.60 24.00 to 24.96
OVERCURRENT PROTECTION Works over 105% of rating and recovers automatically
OVERVOLTAGE PROTECTION[V] 5.75 to 7.00 13.80 to 16.80 17.25 to 21.00 27.60 to 33.60
PROTECTION
CIRCUIT AND OPERATING INDICATION LED (Green)
OTHERS
REMOTE SENSING Not provided
REMOTE ON/OFF Not provided
INPUT-OUTPUT AC3,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At room temperature)
INPUT-FG AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At room temperature)
ISOLATION
OUTPUT-FG AC500V 1minute, Cutoff current = 25mA, DC500V 50MW min (At room temperature)
OPERATING TEMP.,HUMID.AND ALTITUDE *5 -20 to +70C, 20 - 90%RH (Non condensing), 3,000m (10,000 feet) max
STORAGE TEMP.,HUMID.AND ALTITUDE -20 to +75C, 20 - 90%RH (Non condensing), 9,000m (30,000 feet) max
ENVIRONMENT
2
VIBRATION 10 - 55Hz, 19.6m/s (2G), 3minutes period, 60minutes each along X, Y and Z axes
2
IMPACT 196.1m/s (20G), 11ms, once each X, Y and Z axes
AGENCY APPROVALS UL60950-1, C-UL (CSA60950-1), EN60950-1, EN50178, UL508 (Except option -J) Complies with DEN-AN
SAFETY AND
NOISE CONDUCTED NOISE Complies with FCC-B, VCCI-B, CISPR22-B, EN55011-B, EN55022-B
REGULATIONS *8
HARMONIC ATTENUATOR Complies with IEC61000-3-2 class A
PLA-2V.ADJ
PLA15F
SPECIFICATIONS
CASE SIZE/WEIGHT 38X80X73mm [1.50X3.15X2.87 inches] (Excluding terminal block and screw) (WXHXD) / 250g max
OTHERS
COOLING METHOD Convection
*6
WARRANTY WARRANTY 5 years (subject to the operating conditions)
*1 This is the result of measurement of the testing board with capacitors of 22mF and 0.1mF placed at 150 *5 Output po wer derating is required. See 3.2 in Instruction Manual.
mm from the output terminals by a 20 MHz oscilloscope or a ripple-noise meter equivalent to Keisoku- *6 See 3.3 in Instr uction Manual for more details.
Giken RM103.
*7 Consult us about saf ety agency approvals for the models with optional functions.
See 1.6 of Instruction Manual for more details. *8 Consult us about other classes .
When the load factor is 0 - 35%, the switching power loss is reduced by burst operation, which will * Do not use the po wer supply in overcurrent conditions or in unspecified input voltage ranges.
cause ripple and ripple noise to go beyond the specifications. Otherwise the internal components may be damaged.
*2 Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C. * Parallel operation is not possible with this mode.
*3 As f or DC input, consult us for advice. * Sound noise ma y be heard from the power supply when used for pulse load.
*4 Consult us about dynamic load and input response . Measure the output voltage by using the average mode
of the tester to deal with the burst operation at 35% load or less.
Features
- Compact design (Depth: 73mm 2.87inches)
- Low power consumption (1.0W typ AC240Vin, no load at standard model)
- UL508 approved (Except option -J), and complies with SEMI F47
- Various connection interface options (vertical terminal [-T], AMP connector [-J])
Block diagram
FUSE
AC250V2.5A
INRUSH RECTIFIER
NOISE
AC IN 85 - 264V CURRENT AND
FILTER
FILTER
LIMIT
FG
TRANSFORMER
RECTIFIER
CONTROL INVERTER DC OUT
AND
FILTER
OVER CURRENT
Photocoupler
SENSING
CONTROL
Photocoupler
OVER VOLTAGE
PROTECTION
External view
2-M3 Point A
Name plate
TB1 Mounting hole
(Bottom side)
M3.5
AC(L)
AC(N)
FG( )
Output terminal(-)
Output terminal(+)
Output voltage
adjustable potentiometer
Terminal cover
LED
0.5
18 35.5
[0.71] [1.4]
1.5
15.3 (LED)
12.5max 73
[0.6]
[0.49] [2.87]
1.5
14
[0.55]
1.5
11.6 (Potentiometer)
[0.46]
Tolerance : 1 [0.04]
Weight : 250g max
PCB Material/thickness : CEM-3 / 1.6mm [0.06inches]
Chassis material : Electric galvanizing steel board
Case material : Electric galvanizing steel board
2-M3
Dimensions in mm, [ ]=inches 18 46 0.5
Mounting torque : 0.6N m max
- [0.71] [1.81] Mounting hole
Screw tightening torque : 1.0N-m max
PLA-3
1.5
6.5
[0.26]
1.5
12.7 8.2
[0.5]
[0.32]
1.5
17
[0.67]
6.2 9.5
[0.24] [0.37]
20
[0.79]
20 46.5
[0.79] [1.83]
38 80
[3.15]
[1.5]