Ordering information AC-DC Power Supplies Enclosed Type PL A 15 F -O -O PLA15F 1 2 3 4 5 6 1 Series name Example recommended EMI/EMC filter R 2 Single output NAC-04-472 3 Output wattage 4 Universal input 5 Output voltage 6 Optional *7 C : with Coating J : Connector interface T : Vertical terminal block High voltage pulse noise type : NAP series -NO : with DIN rail Low leakage current type : NAM series * A higher current rating EMI/EMC filter may be recommended in view of the See 5.1 in Instruction Manual. other devices that could be connected in parallel with the power supply. *Make sure necessary tests will be carried out on your end equipment with the power supply installed in accordance with any required EMC/EMI regulations. SPECIFICATIONS MODEL PLA15F-5 PLA15F-12 PLA15F-15 PLA15F-24 AC85 - 264 1f (Output derating is required at AC85V - 115V. See 1.1 and 3.2 in Instruction Manual) *3 VOLTAGE V ACIN 100V 0.4typ (Io=90%) CURRENT A ACIN 115V 0.4typ (Io=100%) ACIN 230V 0.25typ (Io=100%) FREQUENCY Hz 50 / 60 (47 - 63) ACIN 100V 72.5typ (Io=90%) 75.5typ (Io=90%) 77.0typ (Io=90%) 78.0typ (Io=90%) INPUT EFFICIENCY % ACIN 115V 73.5typ (Io=100%) 77.0typ (Io=100%) 78.5typ (Io=100%) 79.0typ (Io=100%) ACIN 230V 75.5typ (Io=100%) 78.5typ (Io=100%) 79.5typ (Io=100%) 80.0typ (Io=100%) ACIN 100V 16typ (Io=90%) Ta=25C at cold start INRUSH CURRENT A ACIN 115V 16typ (Io=100%) Ta=25C at cold start ACIN 230V 32typ (Io=100%) Ta=25C at cold start LEAKAGE CURRENT mA 0.30max (ACIN 115V / 240V, 60Hz, Io=100%, According to IEC60950-1 and DEN-AN) VOLTAGE V 5 12 15 24 3 1.3 1 0.7 CURRENT A ACIN 85-115V Output derating is required at ACIN 115V or less (refer to instruction manual 3.2) WATTAGE W ACIN 115V-264V 15.0 15.6 15.0 16.8 *4 LINE REGULATION mV 20max 48max 60max 96max *4 LOAD REGULATION mV 40max 100max 120max 150max 0 to +50C 80max 120max 120max 120max RIPPLE mVp-p *1 -10 to 0C 140max 160max 160max 160max Io=0 to 35% 160max 240max 240max 280max OUTPUT 0 to +50C 120max 150max 150max 150max RIPPLE NOISE mVp-p *1 -10 to 0C 160max 180max 180max 180max Io=0 to 35% 240max 300max 300max 320max 0 to +50C 50max 120max 150max 240max TEMPERATURE REGULATION mV -10 to +50C 60max 150max 180max 290max DRIFT mV *2 20max 48max 60max 96max START-UP TIME ms 200typ (ACIN 115V, Io=100%) *Start-up time is 700 ms typ for less than 1 minute of applying input again from turning off the input voltage. HOLD-UP TIME ms 20typ (ACIN 115V, Io=100%) OUTPUT VOLTAGE ADJUSTMENT RANGE V 4.50 to 5.50 10.80 to 13.20 13.50 to 16.50 21.60 to 26.40 OUTPUT VOLTAGE SETTING V 5.00 to 5.15 12.00 to 12.48 15.00 to 15.60 24.00 to 24.96 OVERCURRENT PROTECTION Works over 105% of rating and recovers automatically OVERVOLTAGE PROTECTION V 5.75 to 7.00 13.80 to 16.80 17.25 to 21.00 27.60 to 33.60 PROTECTION CIRCUIT AND OPERATING INDICATION LED (Green) OTHERS REMOTE SENSING Not provided REMOTE ON/OFF Not provided INPUT-OUTPUT AC3,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At room temperature) INPUT-FG AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At room temperature) ISOLATION OUTPUT-FG AC500V 1minute, Cutoff current = 25mA, DC500V 50MW min (At room temperature) OPERATING TEMP.,HUMID.AND ALTITUDE *5 -20 to +70C, 20 - 90%RH (Non condensing), 3,000m (10,000 feet) max STORAGE TEMP.,HUMID.AND ALTITUDE -20 to +75C, 20 - 90%RH (Non condensing), 9,000m (30,000 feet) max ENVIRONMENT 2 VIBRATION 10 - 55Hz, 19.6m/s (2G), 3minutes period, 60minutes each along X, Y and Z axes 2 IMPACT 196.1m/s (20G), 11ms, once each X, Y and Z axes AGENCY APPROVALS UL60950-1, C-UL (CSA60950-1), EN60950-1, EN50178, UL508 (Except option -J) Complies with DEN-AN SAFETY AND NOISE CONDUCTED NOISE Complies with FCC-B, VCCI-B, CISPR22-B, EN55011-B, EN55022-B REGULATIONS *8 HARMONIC ATTENUATOR Complies with IEC61000-3-2 class A PLA-2 V.ADJ PLA15F SPECIFICATIONS CASE SIZE/WEIGHT 38X80X73mm 1.50X3.15X2.87 inches (Excluding terminal block and screw) (WXHXD) / 250g max OTHERS COOLING METHOD Convection *6 WARRANTY WARRANTY 5 years (subject to the operating conditions) *1 This is the result of measurement of the testing board with capacitors of 22mF and 0.1mF placed at 150 *5 Output po wer derating is required. See 3.2 in Instruction Manual. mm from the output terminals by a 20 MHz oscilloscope or a ripple-noise meter equivalent to Keisoku- *6 See 3.3 in Instr uction Manual for more details. Giken RM103. *7 Consult us about saf ety agency approvals for the models with optional functions. See 1.6 of Instruction Manual for more details. *8 Consult us about other classes . When the load factor is 0 - 35%, the switching power loss is reduced by burst operation, which will * Do not use the po wer supply in overcurrent conditions or in unspecified input voltage ranges. cause ripple and ripple noise to go beyond the specifications. Otherwise the internal components may be damaged. *2 Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C. * Parallel operation is not possible with this mode. *3 As f or DC input, consult us for advice. * Sound noise ma y be heard from the power supply when used for pulse load. *4 Consult us about dynamic load and input response . Measure the output voltage by using the average mode of the tester to deal with the burst operation at 35% load or less. Features - Compact design (Depth: 73mm 2.87inches) - Low power consumption (1.0W typ AC240Vin, no load at standard model) - UL508 approved (Except option -J), and complies with SEMI F47 - Various connection interface options (vertical terminal -T , AMP connector -J ) Block diagram FUSE AC250V2.5A INRUSH RECTIFIER NOISE AC IN 85 - 264V CURRENT AND FILTER FILTER LIMIT FG TRANSFORMER RECTIFIER CONTROL INVERTER DC OUT AND FILTER OVER CURRENT Photocoupler SENSING CONTROL Photocoupler OVER VOLTAGE PROTECTION External view 2-M3 Point A Name plate TB1 Mounting hole (Bottom side) M3.5 AC(L) AC(N) FG( ) Output terminal(-) Output terminal(+) Output voltage adjustable potentiometer Terminal cover LED 0.5 18 35.5 0.71 1.4 1.5 15.3 (LED) 12.5max 73 0.6 0.49 2.87 1.5 14 0.55 1.5 11.6 (Potentiometer) 0.46 Tolerance : 1 0.04 Weight : 250g max PCB Material/thickness : CEM-3 / 1.6mm 0.06inches Chassis material : Electric galvanizing steel board Case material : Electric galvanizing steel board 2-M3 Dimensions in mm, =inches 18 46 0.5 Mounting torque : 0.6N m max - 0.71 1.81 Mounting hole Screw tightening torque : 1.0N-m max PLA-3 1.5 6.5 0.26 1.5 12.7 8.2 0.5 0.32 1.5 17 0.67 6.2 9.5 0.24 0.37 20 0.79 20 46.5 0.79 1.83 38 80 3.15 1.5