Dcmind Brush motor Series Data sheet 89 810 008 89 810 71.4 maxi 2 x M3 at 180, depth 5 mm and 32mm diameter 2 x holes of 2,75 mm diameter, at 120, depth 5 mm and 32mm diameter General characteristics Motor characteristics at (1) 24 Vdc Winding parameters (1) +-10% At no load - A Torque constant mNm/A 56 +-10% +-10% Speed rpm 4 000 Volts/(rad/s) 0,056 Constant electromotive force V / Krpm +-10% Current A 0,11 5,88 Life (2) h 10 000 Resistance Ohms 7,3 +-10% At max efficiency - B Inductance mH 6 Speed rpm 3 300 +-10% Start voltage Volts 0,9 Torque (4) mNm 30 Current demagnetization (magnets at 150 C) A 14 Power output W 10 Current A 0,6 Generic parameters % 72 Efficiency Motor for direct current supply h 5 000 Life (2) Output shaft with ball bearings (20mm from front face) N 100 At nominal load - C Max. Radial force Speed rpm 2 920 +-10% Max. axial force(5) N 70 mNm 50 CEI60068-2-1/2 C -30 / 70 Torque (4) Temperature range W 15 C -40 / 100 Power output Storage temperature 1 (1min 2mA 50Hz) CEI60335 500 Current A Dielectric Vdc 64 CEI60085 Efficiency % Motor insulation class E (120C) 4 000 Life (2) h Enameled wire insulation class F (155C) CEI60068-2-58 Others Salt spray severity 2 190 CEI60529 65 Starting torque mNm Degree of protection IP 3,3 Starting current A EMC CEI61000-4-2 Max. output power W 20 Electrostatic Discharge level 3 CEI61000-4-4 Electrical fast transsient / burst test level 3 CEI61000-4-5 level Motor parameters (1) Surge test 2 10 000 Allowed speed rpm max Radiated emission class B 50 Rated torque mNm Approvals Electrical time constant ms 0,8 Designed in accordance with UL 1004 Mechanical time constant ms 17 ROHS 2002/95/CE Factor torque / speed mNm/rpm 0,0463 EC Dry friction mNm 3 Designed for medical machines using the standard EN60601-1 Viscous friction mNm/krpm 1 Values without tolerences, are average production values. gcm 75 Rotor inertia (1) Cold motor, 20 C ambient temperature /W 11 Thermal Resistance (2) Continuous cycle, one direction Stator poles 2 (3) Continuously rated torque, zero radial and axial loads Collector blades 8 (4) Max torque for continuous operation at 20 C, decrease this value for higher ambient temperature mNm Cogging torque 3 g 340 Weight (g) (5) Pinion or pulley fitting are done at the Crouzet factory, before final assembly. 35 Noise level dBA Curves 4 500 3,5 25 80 Performance / Motor curves (1) 4 000 3 70 Voltage supply Vdc 24 20 3 500 60 2,5 3 000 Output data 50 15 2 2 500 ABCD 40 2 000 Speed rpm 4 000 3 300 2 920 0 1,5 10 30 1 500 Torque (4) mNm 0 3050190 1 20 1 000 0,1 0,6 1,0 3,3 Current A 5 0,5 10 500 - 1015- Power output W 0 0 0 0 Efficiency % - 7264- 0 0,05 0,1 0,15 0,2 0 0,05 0,1 0,15 0,2 Torque (Nm) Torque (Nm) B (max efficiency) C (nominal) Specifications subject to change without notice. Updated february 29, 2012. Crouzet Automatismes 2 rue du Docteur Abel BP59 www.crouzet.com 26902 Valence CEDEX 9 France Speed (rpm) Current (A) Power (W) Efficiency (%) Series 89 810X-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for AC, DC & Servo Motors category: Click to view products by Crouzet manufacturer: Other Similar products are found below : 79207644 805470B40040MY 80807028 808070Y01125Z 808550Y00049Z 823055C10001MWY 82520405 82664024 82802504 R88MK10030H M4E068-EC03-01 M4E068-CF01-01 79265119 80510503 805470A40040MY 805470B40020MY 80627003 808070Y00250Y 808070Y83.33Y 823055A20001MW 825140A40010MP 825290C43.75MX 82714023 82800003 82830009 82810017 R88M-K90010F-S2 R88M-K1K030H-S2 89830012 82840003 82840004 82869011 82524021 82862202 82869006 82861013 80803009 80547015 82862205 R88M-K40030T-B 80527006 82330514 81021118 82524004 89800008 82867009 82662564 82662515 82600041 82524008